Results 201 to 210 of about 2,860,718 (307)

High-Pressure Low-Temperature Study of LnCa₄O(BO₃)₃ (Ln = Pr, Nd, Gd, Er, Tm). [PDF]

ACS Omega
Azrour F, Viennois R, Long J, Granier D, Yu F, Zhang S, Alabarse F, Beaudhuin M, Rouquette J.   +8 more
europepmc   +1 more source

Influence of an Argon/Silane Atmosphere on the Temperature of a Thermal Plasma

Advanced Engineering Materials, EarlyView.
The influence of a silane‐doped argon atmosphere on the chemical composition and temperature of a thermal nontransferring argon plasma is investigated using optical emission spectroscopy. As a result of the high amount of free electrons resulting from the stepwise ionization and dissociation of the silane molecule, even a silane addition of 0.01 vol ...
Lena Kreie, David Kramer, Thomas Scheithauer, Hans Jürgen Maier, Thomas Hassel   +4 more
wiley   +1 more source

In situ characterization of the high pressure - high temperature melting curve of platinum. [PDF]

Sci Rep, 2019
Anzellini S, Monteseguro V, Bandiello E, Dewaele A, Burakovsky L, Errandonea D.   +5 more
europepmc   +1 more source

Thermoelectric Modules Incorporating MgAgSb and Mg3(Sb,Bi)2 Synthesized Using a Melting Method

Advanced Engineering Materials, EarlyView.
A scalable synthesis method for a thermoelectric material of MgAgSb is established. A thermoelectric power module of MgAgSb/Mg3(Sb,Bi)2 is fabricated, showing the conversion efficiency of 7.4% at ΔT = 315 K. The performance is comparable to conventional Bi2Te3 modules when they are operated with an air‐cooled heat exchanger.
Kazuo Nagase, Hironori Ohshima, Kunihiro Kihou, Haruno Kunioka, Ushin Anazawa, Ryosuke Sakagami, Yosuke Goto, Masayuki Murata, Chul‐Ho Lee   +8 more
wiley   +1 more source

Four‐Point Bending Tests at High Temperatures on Commercial MgO‐C Refractory Bricks with and Without Recyclate Considering Different Carbon Contents

Advanced Engineering Materials, EarlyView.
Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm, Lukas Knöchel, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +5 more
wiley   +1 more source

Population of Nonmetallic Inclusions in Liquid High‐Silicon Electrical Steel in Contact With MgO–C Refractories Based on Recyclates and Environmentally Friendly Binders

Advanced Engineering Materials, EarlyView.
The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert, Matheus Roberto Bellé, Florian Kerber, Dinesh Kumar Gunasekar, Hans‐Jörn Weddige, Christos G. Aneziris, Olena Volkova   +6 more
wiley   +1 more source

High-pressure, high-temperature molecular doping of nanodiamond. [PDF]

Sci Adv, 2019
Crane MJ, Petrone A, Beck RA, Lim MB, Zhou X, Li X, Stroud RM, Pauzauskie PJ.   +7 more
europepmc   +1 more source

Chemical reaction at high temperature and high pressure VI : polymorphic transition in ZnP2 at high temperature and high pressure

Chemical reaction at high temperature and high pressure VI : polymorphic transition in ZnP2 at high temperature and high pressure
A new pressure-induced modification of zinc-diphosphide, ZnP_2, has been prepared by the direct union of zinc with phosphorus and also through the polymorphic transitions of both monoclinic and tetragonal ZnP_2. The application of pressures above 20kb combined with temperatures above 150℃ is required for the synthesis. The new modification of ZnP_2 has
openaire  

Engineering Deformation and Failure in Diamond Triply Periodic Minimal Surface Lattices via 3D Wall‐Thickness Grading

Advanced Engineering Materials, EarlyView.
The work demonstrates that strategic wall‐thickness grading in diamond triply periodic minimal surface lattices enables precise tuning of deformation and failure behavior under compression. Different gradation patterns guide how and where the structure collapses, improving energy absorption or promoting controlled brittle failure.
Giovanni Rizza, Danilo Bruson, Manuela Galati, Luca Iuliano   +3 more
wiley   +1 more source

3D‐Printed Serial Snap‐Through Architectures for Programmable Mechanical Response

Advanced Engineering Materials, EarlyView.
A serial snap‐through architecture is realized using compact 3D‐printed von Mises truss units arranged in a staged cascade. Their geometry and boundary conditions program multistage mechanical responses with plateaux and re‐hardening regimes. An inverted‐compliance model predicts these behaviors and enables analytical design of programmable force ...
Filipe A. Santos
wiley   +1 more source