Lattice Structure for Improving Cooling Uniformity in HPDC Mould Corners
Applied SciencesConformal cooling channels have demonstrated significant advantages for cast parts and 3D-printed moulds in the high-pressure die casting (HPDC) process. However, the complex geometry of moulds, characterised by small intrusions, sharp corners, and fins,
Essam Abo-Serie +1 more
doaj +1 more source
Energy efficient engine high-pressure turbine single crystal vane and blade fabrication technology report [PDF]
The objective of the High-Pressure Turbine Fabrication Program was to demonstrate the application and feasibility of Pratt & Whitney Aircraft-developed two-piece, single crystal casting and bonding technology on the turbine blade and vane configurations ...
Giamei, A. F. +2 more
core +1 more source
The study on the integration of Activity Based Costing (ABC) system and six-sigma principle [PDF]
, 2005 Manufacturing organizations are facing much more challenges as compared to the earlier years. The important and crucial decisions have to be taken by the management in continuous basis in order to ensure the survival and competitiveness of company ...
Mohd. Rohani, Jafri +1 more
core
Advanced Engineering Materials, EarlyView.Micro‐Raman spectroscopy is applied to characterize corrosion products in a recycled‐based MgO–316L steel composite anode after molten salt electrolysis. A depth‐dependent Fe–O/Fe–Al–O layer sequence of magnetite, hercynite, and an Al‐doped magnetite transition zone is identified.
Felix Drechsler +9 more
wiley +1 more source
Mg-Al-RE Magnesium Alloys for High-Pressure Die-Casting
Archives of Foundry Engineering, 2014 Experimental Mg-Al-RE type magnesium alloys for high-pressure die-casting are presented. Alloys based on the commercial AM50 magnesium alloy with 1, 3 and 5 mass % of rare earth elements were fabricated in a foundry and cast in cold chamber die-casting ...
Braszczyńska-Malik K.N.
doaj +1 more source
Case Study of Large Three-Dimensional-Printed Slider with Conformal Cooling for High-Pressure Die Casting. [PDF]
3D Print Addit Manuf, 2023 Andronov V +4 more
europepmc +1 more source
Advanced Engineering Materials, EarlyView.A carbon‐free, as‐sintered MgO–steel cermet anode, fabricated via cold isostatic pressing using MgO–C refractory recyclate, was evaluated under laboratory‐scale K‐cryolite electrolysis at 800°C. Operation at this reduced temperature, combined with the electrolyte's limited electrical conductivity, led to an increase in cell voltage.
Farhan Hossain +7 more
wiley +1 more source
Microstructural Characteristics of High-Pressure Die Casting with High Strength-Ductility Synergy Properties: A Review. [PDF]
Materials (Basel), 2023 Yang Q, Wu X, Qiu X.
europepmc +1 more source
Interaction of Ladle Slag With Varying SiO2 Content and Recyclate‐Based MgO–C Refractories
Advanced Engineering Materials, EarlyView.Ladle slags (CaO/Al2O3 = 1) with 1–20 wt% SiO2 were investigated in contact with industrial MgO–C refractories fabricated from fresh magnesia and 50 wt% recyclate. The sessile drop method at 1600°C reveals intensive gas formation, delayed slag infiltration in recyclate‐based samples, and, under high‐SiO2 slag, formation of a dense MgAl2O4‐rich ...
Anton Yehorov +6 more
wiley +1 more source
Influence of High-Pressure Die Casting Parameters on the Cooling Rate and the Structure of EN-AC 46000 Alloy. [PDF]
Materials (Basel), 2022 Kowalczyk W +4 more
europepmc +1 more source