Results 221 to 230 of about 167,316,237 (293)

Thermal Deformation in Non-Planar Large-Scale Additive Manufacturing of ABS: Experimental and Finite Element Analysis. [PDF]

Materials (Basel)
Aladag M, Tek E, Akeloglu MA, Dubicki A, Zgłobicka I, Eyercioglu O, Kurzydlowski KJ.   +6 more
europepmc   +1 more source

High Throughput Aerosol Jet Printing to Operationalize High Aspect Ratio Patterning

Advanced Materials Technologies, EarlyView.
High‐throughput aerosol jet printing poses distinct limiting mechanisms to the printing process. These include rapidly changing ink chemistries, atomization instabilities, and liquid‐phase spreading. The combination of in‐line heating, process monitoring, and traditional optimization procedures enables rapid printing of high‐aspect‐ratio structures ...
Bella I. Guyll, Md Mahdi Ul Ishtiaque, Md Ramjan Ali, Todd A. Kingston, Ethan B. Secor   +4 more
wiley   +1 more source

Use of three-dimensional-printed models for preoperative planning in endoscopic endonasal surgery for tuberculum sellae meningioma: A case report and literature review. [PDF]

Surg Neurol Int
Escamilla-Chávez E, Hernández González JC, Pérez De Anda MY, Valdivia-Hernández A, Cortés-Monterrubio RA, Vega-Moreno DA, Velasco-Torres HS.   +6 more
europepmc   +1 more source

Microfluidic Droplet Plate Preserving Single Human Induced Pluripotent Stem Cell‐Derived Cardiomyocytes Morphology and Function

Advanced Materials Technologies, EarlyView.
We introduce a novel method combining microfluidics, optogenetics, and human induced pluripotent stem cell (iPSC) technology to encapsulate single iPSC‐derived cardiomyocytes (iPSC‐CMs) in an optimal environment for functional characterization. This method enables direct genotype‐phenotype correlation for genetic studies and high‐throughput screening ...
Xiao‐Ting Wang, Rachel P. White, Yashasvi Tharani, Michael A. Finocchiaro, Leona M. Ripple, Maksymilian Prondzynski, Tania Konry, Vassilios J. Bezzerides   +7 more
wiley   +1 more source

Risk factors of postoperative complications after F/B-TEVAR for aortic arch lesions: a multicenter retrospective analysis. [PDF]

Front Cardiovasc Med
Hu J, Han Y, Wang Y, Jin Y, Zhao Z, Liu Z.   +5 more
europepmc   +1 more source

In‐House Manufacturing of 3D ECM Culture Chips via Vacuum Thermoforming for Enhanced Imaging Applications

Advanced Materials Technologies, EarlyView.
Desktop vacuum thermoforming enables rapid, low‐cost fabrication of 96‐channel polystyrene culture chips with very thin imaging interfaces. The resulting platform supports cell lines, primary cells, and patient‐derived organoids, and enables high‐resolution confocal microscopy and single‐cell visualization, providing an accessible approach for advanced
Aleksandra Fomina, Adam Tam, Jennifer Lam, Nila C. Wu, Nancy T. Li, Alison P. McGuigan   +5 more
wiley   +1 more source

Patient-specific static and dynamic 3D-printed models for planning endovascular repair of complex aortic disease with physician-modified stent grafts. [PDF]

CVIR Endovasc
Gong Q, Yang Y, Deng H, Hu X, Zhang J, Cao S, Song H, Zhou Q.   +7 more
europepmc   +1 more source

Liquid Crystal Elastomer Actuator Matrix for Large Area Applications

Advanced Materials Technologies, EarlyView.
A scalable approach is used to manufacture a digitally‐controllable, 2D 5 × 5 actuator matrix. The elements of the matrix are produced by direct ink writing of a liquid crystal elastomer ‘artificial muscle’ on large‐area flexible thin‐film heaters. In optimizing the low‐power actuators, multiple heater designs and substrate materials are investigated ...
Giulia Spallanzani, Bart Peeters, Danqing Liu, Peter Zalar, Hylke B. Akkerman, Jeroen A. H. P. Sol   +5 more
wiley   +1 more source

Coacervates as bio-inspired intermediates for materials processing.

Chem Commun (Camb)
Graafsma C, Jaber MR, Monreal Santiago G, Kamperman M.   +3 more
europepmc   +1 more source

Fully Printed Ionic Diodes from Polymerizable Ionic Liquids. [PDF]

ACS Nano
Kane AQ, Yang E, Truby RL.
europepmc   +1 more source