Results 31 to 40 of about 314,572 (210)
IEEE Access, 2021 In this paper, linearly and circularly polarized single-layer Substrate Integrated Waveguide (SIW) horn antennas with nearly equal half power beamwidths in principal planes for the 24 GHz ISM band are designed.
Jaroslav Zechmeister +2 more
doaj +1 more source
Advanced Functional Materials, EarlyView.A sequential dual‐alignment strategy independently programs the orientation of conductive metal‐organic framework (c‐MOF) microrods and liquid crystals within a composite film. This approach creates an asymmetric bilayer structure that enables precise, multi‐responsive actuation.
Taegyun Hong +5 more
wiley +1 more source
Advanced Functional Materials, EarlyView.The mantis shrimp telson reveals how ridged biological shields control deformation under impact. Inspired by this architecture, telson‐inspired ridged curved shells transform ridge geometry and macroscopic curvature into bidirectional snap‐through, tunable stiffness, and enhanced hysteretic energy dissipation for multifunctional architected materials ...
Phani Saketh Dasika +5 more
wiley +1 more source
Advanced Materials, EarlyView.Anion‐exchange doping of conjugated polymers is an effective way to achieve high conductivities. Here, we report over 2000 S cm−1 electrical conductivity for doped P(g3BTTT). In addition, we show that P(g3BTTT) sustains exceptionally high doping levels without any drop in the charge mobility.
Basil Hunger +14 more
wiley +1 more source
The Use of 3D Printing Technology for Manufacturing Metal Antennas in the 5G/IoT Context
Sensors, 2021 With the rise of 5G, Internet of Things (IoT), and networks operating in the mmWave frequencies, a huge growth of connected sensors will be a reality, and high gain antennas will be desired to compensate for the propagation issues, and with low cost ...
Diogo Helena +3 more
doaj +1 more source
Printed transition for SIW horn antennas - Analytical model
, 2012 A printed transition is proposed to overcome problems limiting the performances of SIW horn antennas when built in thin substrates (thickness <λ 0/10). An analytical model to analyze its behavior is given along with design guidelines.
Esquius-Morote, Marc +5 more
core +1 more source
Conformal Coating and Transfer of 2D Nanomaterials via Dynamic Interface Engineering
Advanced Materials Interfaces, EarlyView.This review discusses conformal coating and transfer of two‐dimensional (2D) nanomaterials with a focus on dynamic interface engineering. By actively regulating nanosheet transport and interfacial contact during film formation, recent dynamic coating strategies overcome the limitations of conventional passive approaches and enable geometry‐adaptive ...
Seungyeon Kim +4 more
wiley +1 more source
Wood‐Derived Nanocellulose‐Biocarbon Fresnel‐Zone Plate Lenses for Sub‐THz Frequency Applications
Advanced Materials Technologies, EarlyView.Wood‐derived nanocellulose and lignin‐based biocarbon were combined to fabricate fully bio‐based Fresnel zone plate (FZP) lenses for sub‐terahertz frequencies. These sustainable FZP lenses exhibit low dielectric loss and high directivity, achieving performance comparable to that of metallic references, and remain functional under environmental stress ...
Riikka Haataja +9 more
wiley +1 more source
Analysis of Horn Antennas in Receiving Mode as an EM Field Sensor
International Journal of Antennas and Propagation, 2012 Electromagnetic (EM) field measurement uses antenna in receiving mode as EM field sensor (EMFS). FDTD technique is applied to analyze the horn antenna in this mode.
Maifuz Ali, Seong-Ook Park
doaj +1 more source
Wide-band horn antennas of low profile
, 2021 With the rapid development of ultra-wideband technology and with the advantages of high capacity, large bandwidth, and high speed, ultra-wideband antennas have been widely used in fields such as electromagnetic compatibility, electromagnetic measurement,
Chen, Zihao
core