Results 11 to 20 of about 1,121,726 (329)

Improved Perovskite/Carbon Interface through Hot-Pressing: A Case Study for CsPbBr3-Based Perovskite Solar Cells

ACS Omega, 2022
Due to the low cost and printable nature of the carbon paste, carbon-based perovskite solar cells (PSCs) are attractive for real application. However, the poor contact at the perovskite/carbon interface obviously hinders the achievable fill factor of the
Teng Zhang, Chengben Liu, Zhi Li, Baohua Zhao, Youru Bai, Xinmei Li, Wenwen Liu, Yanli Chen, Zhaobin Liu, Xiyou Li   +9 more
semanticscholar   +1 more source

Synergies between Fibrillated Nanocellulose and Hot-Pressing of Papers Obtained from High-Yield Pulp

Nanomaterials, 2023
To extend the application of cost-effective high-yield pulps in packaging, strength and barrier properties are improved by advanced-strength additives or by hot-pressing.
Carlos Negro, Gunilla Pettersson, Amanda Mattsson, Staffan Nyström, Jose Luis Sanchez-Salvador, Angeles Blanco, Per Engstrand   +6 more
doaj   +1 more source

Research on application of hot isostatic pressing technology in the field of nickel-based cast superalloys

Cailiao gongcheng, 2021
Nickel-based cast superalloy is one of the main materials applied in the manufacture of aeroengine and gas turbine,and it is widely applied in aerospace,energy industry and shipbuilding industries etc.The rapid development of modern aviation industry is ...
SONG Fu-yang, ZHANG Jian, GUO Hui-ming, ZHANG Mai, ZHAO Yun-song, SHA Jiang-bo   +5 more
doaj   +1 more source

Mechanism of improved intermediate temperature plasticity of nickel-base single crystal superalloy with hot isostatic pressing

Journal of Materials Research and Technology, 2021
In this work, we investigate the effect of hot isostatic pressing on the intermediate temperature tensile property of nickel-base single crystal superalloy.
Weidong Xuan, Xiangyu Zhang, Yujuan Zhao, Junjie Li, Baojun Wang, Xingfu Ren, Zhongming Ren   +6 more
doaj   +1 more source

Sintering behavior of alumina whisker reinforced zirconia ceramics in hot oscillatory pressing

Journal of Advanced Ceramics, 2022
Alumina whisker reinforced zirconia ceramic composite was prepared by both hot oscillatory pressing (HOP) and conventional hot pressing (HP). The results show that compared with HP, HOP can significantly increase the final density and densification rate ...
Hongtian He, Rui Zhao, Hongyi Tian, G. Shao, Hailong Wang, B. Fan, Hongxia Lu, Hongliang Xu, Rui Zhang, Li-nan An   +9 more
semanticscholar   +1 more source

Structure and characteristics of the hot pressed hydroxyapatite/poly-L-lactide composite [PDF]

Science of Sintering, 2002
Hydroxyapatite/poly-L-lactide (HAp/PLL) composite biomaterial can be obtained by different processing methods. Three-dimensional blocks of HAp/PLLA composite biomaterial with mechanical characteristics close to the natural bone tissue can be obtained by ...
Ignjatović Nenad L., Suljovrujić Edin H., Stojanović Z., Uskoković Dragan P.   +3 more
doaj   +1 more source

Thermoelectric property studies on thallium-doped lead telluride prepared by ball milling and hot pressing [PDF]

, 2010
Thallium doping into lead telluride has been demonstrated to increase the dimensionless thermoelectric figure-of-merit (ZT) by enhancing Seebeck coefficient due to the creation of resonant states close to Fermi level without affecting the thermal ...
Chen, Gang, Ren, Z. F., Snyder, G. Jeffrey, Wang, Dezhi, Wang, Heng, Wang, Hengzhi, Wang, Hui, Wang, Xiaowei, Yu, Bo, Zhang, Qinyong   +9 more
core   +1 more source

Pre-pressing and Pre-heating via Hot-Air/Hot-Steam Process for the Production of Binderless Medium-Density Fiberboards

BioResources, 2016
The hot-air/hot-steam process was used for the first time as a combined pre-pressing and pre-heating system for the production of medium-density fiberboards (MDF) at the pilot scale. Pre-heating systems are designed to pre-heat fiber mats before pressing
Markus Euring, Alexander Kirsch, Alireza Kharazipour   +2 more
doaj   +1 more source

Hot-pressing process modeling for medium density fiberboard (MDF) [PDF]

, 2001
In this paper we present a numerical solution for the mathematical modeling of the hot-pressing process applied to medium density fiberboard. The model is based in the work of Humphrey[82], Humphrey and Bolton[89] and Carvalho and Costa[98], with some ...
Nigro, Noberto M., Storti, Mario A.
core   +5 more sources

Mechanical Properties of LPBF-Built Titanium Lattice Structures—A Comparative Study of As-Built and Hot Isostatic Pressed Structures for Medical Implants

Metals, 2022
We compare different lattice structures with various elementary cell sizes built by laser powder bed fusion with and without hot isostatic pressing as post treatment.
Benedikt Adelmann, Ralf Hellmann
doaj   +1 more source