Results 11 to 20 of about 151,122 (359)
Materials Research Express, 2020 Nickel-based superalloys are widely used at elevated temperature applications because of their high corrosion and oxidation resistance characteristics as well as high stability.
Vahid Tavakoli Targhi +3 more
doaj +1 more source
Pitting corrosion of galvanized pipes in hot water supply systems [PDF]
E3S Web of Conferences, 2021 The mechanism of pitting corrosion of galvanized pipes in hot water supply systems is considered. The analysis of the literature to determine the conditions and mechanism that cause abnormally rapid corrosion of steel galvanized water pipes in water ...
Andrianov Alexey
doaj +1 more source
npj Materials Degradation, 2021 The hot corrosion behavior of nickel-based single-crystal superalloy after drilling is investigated at 900 °C. The characteristics of hot corrosion after drilling which are different from normal hot corrosion are reflected in the formation of a more ...
Zehao Chen +4 more
doaj +1 more source
Advanced burner-rig test for oxidation-corrosion resistance evaluation of MCrAlY/superalloys systems [PDF]
, 2006 Protective coatings are used on gas turbine components to enable them to survive in engine-operating conditions. This study presents a recently developed cyclic burner-rig test that is used to simulate helicopter engine conditions and to assess the ...
Andrieu, Eric +3 more
core +3 more sources
Application Status of Corrosion and Protection of Coastal Railway OCS Carbon Steel Components [PDF]
Cailiao Baohu, 2021 The current anti - corrosion standards of carbon steel components for OCS (Overhead Catenary System) of electrified railway in China were briefly discussed, and the corrosion situation of OCS steel components of coastal railways was analyzed.
WANG Qing, YANG Jia, QI Fu - gang
doaj +1 more source
Performance Comparison Between Isothermal Hot Corrosion And In Situ Cyclic Hot Corrosion of Nickel-Based Superalloys [PDF]
Oxidation of Metals, 2021 AbstractAlthough a lot of work has been done to understand both major mechanisms of hot corrosion, namely type I (high-temperature hot corrosion) and type II (low temperature hot corrosion), there is very little information available on more representative cyclic performance in these regimes.
Syed, A. U. +8 more
openaire +4 more sources
Role of hydrogen chloride in hot salt stress corrosion cracking of titanium aluminum alloys [PDF]
, 1967 Hot salt stress corrosion cracking of titanium aluminum alloys in presence of anhydrous hydrogen ...
Louthan, M. R., Jr., Ondrejcin, R. S.
core +2 more sources
Study on Phosphating Pretreatment and Electrophoretic Properties of Hot-Based Zn-Al-Mg Steel Plate [PDF]
Cailiao Baohu, 2023 The coating and corrosion resistance of hot-based zinc-aluminium-magnesium steel sheet was investigated by means of SEM，XRD，film weight，film thickness，roughness，corrosion resistance，adhesion，stone resistance，water resistance and other comprehensive ...
LONG Yuan, ZOU Ying, HAO Yu-lin, ZHOU Jian, LIU Wu-hua, LIU Hua-sai, LI Xue-tao, WANG Chao-bin
doaj +1 more source
Salt-deposit hot corrosion behaviors of directionally solidified DZ466 superalloy
工程科学学报, 2015 Hot corrosion behaviors of DZ466 alloy at 850℃ and 950℃ were investigated by using a NaCl/Na2SO4salt-deposit method. It is found that there are three corrosion layers on the alloy.
DING Xian-fei +5 more
doaj +1 more source
Materials & Design, 2021 Hot corrosion behavior of three nickel-based single crystal superalloys with different key alloying elements (including Re, Cr, Al and Ti) contents in molten Na2SO4 salt at 900 °C was investigated.
Peng Song +9 more
doaj +1 more source