Results 11 to 20 of about 25,407 (285)
Effect of randomly distributed fibers on residual stress of SiC/GH4738 composites
Composites Part C: Open Access, 2021 In this paper, the model of SiC reinforced superalloy composite with different fiber content is established by Monte Carlo simulation method. The process of hot isostatic pressing of SiC reinforced superalloy composite is simulated, and the residual ...
Yanju Wang +4 more
doaj +1 more source
Energies, 2022 The transport characteristics and kinetics of moisture in hot-pressing are crucial to controlling the insulated paperboard drying process. The effects of operating temperature (110, 120, and 130 °C) on moisture transfer characteristics of an insulated ...
Lingbo Kong +3 more
doaj +1 more source
Study on Microstructure and Mechanical Properties of Powder Metallurgy TA15 Titanium Alloy [PDF]
MATEC Web of Conferences, 2020 TA15 pre-alloyed powder chosen in this paper is made by plasma rotating electrode method. The powders were used to prepare fully dense TA15 alloy ingots by the means of hot isostatic pressing(HIP) forming technology.
Zhang Zhiyong +5 more
doaj +1 more source
Fracture and Structural Integrity, 2023 In the present study, the impact behavior of gravity casting AlSi10Mg alloy was evaluated with an instrumented Charpy pendulum. The effect of hot isostatic pressing, also followed by a T6 treatment, was analyzed in comparison with samples in the as-cast,
Luca Girelli +6 more
doaj +3 more sources
Optimization Design of Bamboo Filament Decorated Board Process Based on Response Surface
BioResources, 2022 Bamboo filament decorated board is a new kind of bamboo and wood composite material. In this material, melamine-urea-formaldehyde (MUF) modified resin impregnated paper is used as the bonding material between bamboo filament decoration material and ...
Hui Li +6 more
doaj +2 more sources
Effect of Y2O3 on properties of iron-based diamond tools
Jin'gangshi yu moliao moju gongcheng, 2022 The effects of hot pressing pressure, sintering temperature and Y2O3 content on the hardness, the density, the flexural strength and the fracture morphology of the iron-based matrix were studied by orthogonal test, and the better sintering process ...
Lu WEN +4 more
doaj +1 more source
Simulation of the hot isostatic pressing process
PNRPU Mechanics Bulletin, 2021 This work, models the compaction of a dispersed body under the conditions of a hot isostatic pressing (HIP) cycle using the example of the manufacture of compacts from VZh159ID powder and Inconel alloy 718. For the research, VZh159ID powder of fraction -70 + 25 μm, bulk density of 3.77 g/cm3 (4.83 g/cm3 after tapping), fluidity of 2.3 g/s, specific ...
A. A Khlybov +6 more
openaire +1 more source
Enhanced Patterned Cocatalyst TiO2/Fe2O3 Photoanodes for Water-Splitting
Nanoscale Research Letters, 2021 In this study, we used a hot-pressing process to enhance the photocatalytic properties of TiO2/Fe2O3 bimetallic oxide with a periodic patterned structure on the surface to increase photon absorption for photocatalysis in the oxygen evolution reaction for
Wei-Hsuan Hung +3 more
doaj +1 more source
Effects of Hot Pressing Temperature and Pressure on Dielectric Properties of Aramid Insulating Paper
Energies, 2022 The hot pressing parameters and fiber ratio have an important influence on the dielectric properties of aramid insulating paper. In order to deeply explore its influence and the mechanism behind it, aramid insulating papers were made with different hot ...
Yuanxin Yao +5 more
doaj +1 more source
BioResources, 2016 The hot-air/hot-steam process was used for the first time as a combined pre-pressing and pre-heating system for the production of medium-density fiberboards (MDF) at the pilot scale. Pre-heating systems are designed to pre-heat fiber mats before pressing
Markus Euring +2 more
doaj +1 more source