Results 251 to 260 of about 266,903 (286)

Stimuli-Responsive Afterglow from Luminescent Liquid Crystal Elastomers. [PDF]

Adv Mater
Yue L, Debije MG, Schenning APHJ.
europepmc   +1 more source

Valorization of Recovered Mine Timber as a Secondary Feedstock for Medium-Density Fiberboard Manufacturing. [PDF]

Materials (Basel)
Dudeva V, Savov V, Antov P, Aleksandrov Y.   +3 more
europepmc   +1 more source

Optimized Hot Pressing of High-Speed Steel-Bronze Composites for Diamond-Reinforced Tool Applications. [PDF]

Materials (Basel)
Průša F, Romański A, Książek M, Thürlová H, Tyrała D, Kratochvíl P, Konstanty J, Voňavková I, Růžička F, Riedl J, Dąbrowski R, Sołek K, Pokorný J, Jaworska L.   +13 more
europepmc   +1 more source

Enhancing Solid-State Li-Ion Batteries with MOF-Polymer Composite Electrolytes-Effect Mechanisms and Interface Engineering. [PDF]

Gels
Chen T, Reddy NP, Li M.
europepmc   +1 more source

Some of the next articles are maybe not open access.

Related searches:

High-Pressure Combinatorial Process Integrating Hot Isostatic Pressing

ACS Combinatorial Science, 2013
A high-pressure combinatorial process integrating hot isostatic pressing (HIP) was developed by providing a reaction vessel with a high-pressure tightness based on a commercial flange. The reaction vessel can be used up to 200 MPa and 500 °C under HIP processing condition. Preparation of spinel-type MgAl2O4 from Mg(OH)2, Al(OH)3 and AlOOH was performed
Kenjiro, Fujimoto, Hiroki, Morita, Yuji, Goshima, Shigeru, Ito   +3 more
openaire   +2 more sources

CMC-Processing from Powders by Hot-Pressing

Advances in Science and Technology, 2006
Hot pressing is an effective way to densify powder compacts, especially during the inclusion of a second phase, such as particles, whiskers or fibers. In the present study, SiC/SiC and C/SiC composites were prepared by hot pressing via liquid phase sintering. Nano-SiC powder was used for matrix formation with sintering additives.
Shao Ming Dong, Yu Sheng Ding, Zhen Wang, Qing Zhou, Xiang Yu Zhang, Dong Liang Jiang, Akira Kohyama   +6 more
openaire   +1 more source

Wear processes in hot forging press tools

Materials & Design, 1995
Abstract In the hot forging industry, die life is an important process factor because of the cost involved in lost production, replacement of die blocks, resinking of cavities and operative handling of the dies. There is still no consensus, however, on the type of wear affecting dies or the dominant reason for die failure, which varies from one ...
E. Summerville, K. Venkatesan, C. Subramanian   +2 more
openaire   +1 more source

Optimizing the Hot Isostatic Pressing Process

Materials and Manufacturing Processes, 2003
Abstract A genetic algorithm (GA) is used to optimize the hot isostatic pressing (HIPing) process for beryllium powder. The GA evaluates a HIPing model with different processing schedules in an effort to minimize temperature, pressure, processing time, ramp rates, grain growth, and distance to target relative density.
openaire   +1 more source

Process Optimization for Multi-Veneer Hot-Press Drying

Drying Technology, 2014
The 1 to 20 veneers of Eucalyptus saligna were dried using a hot press with a pressure of 0.1–0.4 MPa and a temperature of 120–160°C.The energy consumption and properties of the veneers were examin...
Chenjing Han, Tianyi Zhan, Jinmei Xu, Jinghui Jiang, Jianxiong Lu   +4 more
openaire   +1 more source