Results 261 to 270 of about 8,222 (273)

Investigations on Hot Tearing Susceptibility and its Mechanism of Mg-Zn-Y Alloys

Materials Science Forum, 2016
Hot tearing sensitivity of MgZn2.5YxZr0.5(x=0.5,1,2,4,6) alloys were predicted by using thermodynamic calculations based on Clyne-Davies’ model, and verified experimentally by using a "T"-type hot tearing permanent-mold equipment. The hot tearing mechanism with different Y content of MgZn2.5YxZr0.5 alloys was investigated. The results demonstrated that
Zheng Liu, Li Liu, Si Bo Zhang, Zhi Wang, Ping Li Mao, Yue Wang   +5 more
openaire   +1 more source

Hot tearing susceptibility of TiB₂-reinforced Al–5Cu matrix composite

Journal of Composite Materials, 2015
This work investigated the hot tearing susceptibility of TiB2 reinforced Al–5Cu matrix composites. The results indicated that the hot tearing susceptibility of Al–5Cu alloy was significantly decreased when the TiB2 content was less than 3%. The improvement was attributed to the TiB2 particles promoted the grain refinement.
Xiaobo Zhang, Jing Sun, Mingliang Wang, Yijie Zhang, Naiheng Ma, Haowei Wang   +5 more
openaire   +1 more source

Hot Tearing Susceptibility and Fluidity of Semi-Solid Gravity Cast Al-Cu Alloy

Solid State Phenomena, 2006
Aluminum-copper alloys offer both high strength and excellent ductility suitable for a number of automotive applications to reduce vehicle weight; however, the alloys are difficult to cast because of their tendency for hot tearing. In this work, semi-solid gravity casting of an aluminum-copper alloy, B206, was conducted in constrained rod casting molds
J. Wannasin, David Schwam, J.A. Yurko, C. Rohloff, G. Woycik   +4 more
openaire   +1 more source

Effect of Yttrium on Hot Tearing Susceptibility of Mg–6Zn–1Cu–0.6Zr Alloys

International Journal of Metalcasting, 2019
The effect of Yttrium (Y) addition on hot tearing susceptibility of Mg–6Zn–1Cu–xY–0.6Zr (x = 0, 1, 2, 3) alloys was investigated using a constrained rod casting apparatus which monitored the hot tearing formation with a load sensor and a data acquisition system.
Guannan Zhu, Zhi Wang, Wuyan Qiu, Ye Zhou, Le Zhou, Feng Wang, Zheng Liu, Pingli Mao   +7 more
openaire   +1 more source

Crack formation of camshaft castings: Hot tearing susceptibility and root causes

Engineering Failure Analysis, 2023
Yankang Zhu, Kangkang Zhou, Gangqiang Xu, Cangsu Xu, Xiaolu Li, Yuntang Li, Bingqing Wang, Francis Oppong   +7 more
openaire   +1 more source

Study on the Hot Tearing Susceptibility of Mg-4Zn-xSn-1Ca Alloys

International Journal of Metalcasting, 2022
Feng Leng, Feng Wang, Xudong Du, Zhi Wang, Zheng Liu, Pingli Mao   +5 more
openaire   +1 more source

Simulating the hot tearing susceptibility of steel cast flange

International Journal on Interactive Design and Manufacturing (IJIDeM), 2023
openaire   +1 more source

Effect of Ca/Al ratio on hot tearing susceptibility of Mg–Al–Ca alloy

Journal of Alloys and Compounds, 2022
Xudong Du, Feng Wang, Zhi Wang, Le Zhou, Ziqi Wei, Zheng Liu, Pingli Mao   +6 more
openaire   +1 more source

Effect of AlN reinforcement particles on hot-tearing susceptibility of AlN/AZ91D composites

Materials Today Communications, 2023
Jian Huang, Zhongming Zhang, Changlin Yang, Bin Zhang, Yunxia Sun, Tuo Liang, Tian Li, Zhu Mao, Jiemin Zu, Jingchao Wang, Ruiru Cai, Jianfeng Liu   +11 more
openaire   +1 more source

Hot Tearing Susceptibility of High Speed Laser Welding Invar Sheet

Chinese Journal of Lasers, 2011
倪加明 Ni Jiaming, 李铸国 Li Zhuguo, 吴毅雄 Wu Yixiong   +2 more
openaire   +1 more source