Results 31 to 40 of about 1,850 (153)
BiofabricationBone tissue engineering (BTE) seeks to overcome the limitations of traditional bone repair methods, such as autografts and allografts, which are often limited by availability, donor-site morbidity, immune rejection, and infection risks.
Ane Albillos Sanchez +5 more
semanticscholar +1 more source
Journal of Magnesium and Alloys, 2023 Since the introduction of Tesla's Giga-Casting process, the automotive industry has widely accepted the concept of super-sized structural components due to their significant potential for enhancing the light-weighting of both electric and internal ...
Tian Li +8 more
doaj +1 more source
Microstructure characterization and corrosion resistance properties of Pb-Sb alloys for lead acid battery spine produced by different casting methods. [PDF]
PLoS ONE, 2018 The aim of this study is to find out the microstructure, hardness, and corrosion resistance of Pb-5%Sb spine alloy. The alloy has been produced by high pressure die casting (HPDC), medium pressure die casting (AS) and low pressure die casting (GS ...
Asiful H Seikh +5 more
doaj +1 more source
METAL Conference Proeedings, 2023 This research article introduces a methodology for studying the operational wear of experimental shaped parts of moulds for high-pressure die casting (HPDC) of zinc alloys. The study includes roughness analysis and geometric dimensioning and tolerancing (
K. Koza +7 more
semanticscholar +1 more source
Effects of Pouring Temperature on Microstructure and Mechanical Properties of the A356 Aluminum Alloy Diecastings [PDF]
Materials ResearchDiecastings of the A356 aluminum alloy were produced by rheo-diecasting (RDC) and High pressure die casting (HPDC), the microstructures of primary solidification, secondary solidification and eutectic Si of diecastings with different pouring temperature ...
Ming Li, Yuandong Li, Hongwei Zhou
doaj +2 more sources
Challenges and Support when Introducing AM in HPDC Tooling [PDF]
, 2019 When manufacturing tooling inserts for HPDC (High Pressure Die Casting), several manufacturing steps such as milling, heat treatment, electro discharge machining and finally surface treatment are involved. By instead manufacturing the insert by SLM (Selective laser melting), the process is expected to be quicker and with less material waste compared to
Roland Stolt +2 more
openaire +3 more sources
Metamodels’ Development for High Pressure Die Casting of Aluminum Alloy
Metals, 2021 Simulation is a very useful tool in the design of the part and process conditions of high-pressure die casting (HPDC), due to the intrinsic complexity of this manufacturing process.
Eva Anglada +3 more
doaj +1 more source
Influence of HPDC Process Parameters on the Microstructure of EC Electromotor Housing
Metals, 2023 The mechanical properties of high-pressure die-casted parts are directly influenced by their microstructure. This article aims to evaluate the effect of the fast-shot speed on the structural component and overall microstructure for two geometrically ...
M. Brůna +3 more
semanticscholar +1 more source
Numerical modelling of porosity with combined gas and shrinkage effects in HPDC
IOP Conference Series: Materials Science and Engineering, 2023 High-pressure die casting is a manufacturing process in which near-net-shape components are produced rapidly under a pressurized environment. However, due to the relatively higher cooling rate prevailing during the process, isolated liquid pockets form ...
U. Godwal +5 more
semanticscholar +1 more source
Corrosion Behavior of Gravity Cast and High-Pressure Die-Cast AM60 Mg Alloys with Ca and Y Addition
Metals, 2022 In this study, the microstructure and related corrosion behavior of AM60 alloys with/without Ca and Y addition upon gravity casting (GC) and high-pressure die-casting (HPDC) are investigated by means of SEM/EDS characterization, immersion/salt spray test,
Hui Yu +9 more
doaj +1 more source