Results 201 to 210 of about 98,352 (281)

Development of a Fiber Bundle Cell Framework for Rapid, Reliability‐Based Analysis and Design of Pseudo‐Ductile Thin‐Ply Hybrid Composites

Polymer Composites, EarlyView.
Application of the fiber bundle cell model for design or prediction of pseudo‐ductility. ABSTRACT In this study, we developed and validated a novel fiber bundle cell (FBC) framework to enable rapid, reliability‐anchored design of pseudo‐ductile thin‐ply carbon/glass hybrid composites.
László M. Vas, Roland Petrény
wiley   +1 more source

Application and Improvement of Ultradeep Fractured Reservoir Effective Stimulation Reservoir Volume Technology. [PDF]

ACS Omega
Zhang Z, Hou B, Weng D, Cai B, Yang Z, Zhao J.   +5 more
europepmc   +1 more source

Microstructure–Mechanical Response Relationship in Discontinuous Fiber‐Reinforced SMC Composites: Damage Mechanisms

Polymer Composites, EarlyView.
Architecture of SMC composites. ABSTRACT The mechanical performance of sheet molding compounds (SMCs) is dependent on microstructural characteristics determined by material composition and processing conditions. The study investigates standard SMCs, advanced SMCs (A‐SMCs), and low‐density SMCs (LD‐SMCs) under quasi‐static and fatigue loading to ...
Mohammadali Shirinbayan
wiley   +1 more source

Analysis and Comparison of Natural Shear and Induced Tensile Fractures for Caprock Leakage Assessment. [PDF]

Transp Porous Media
Achuo Dze S, Phillips T, Najafi-Silab R, Perez S, Bultreys T, Novak V, Schlepütz CM, Cnudde V, Doster F, Singh K, Bisdom K, Busch A.   +11 more
europepmc   +1 more source

Fluid velocity based simulation of hydraulic fracture-a penny shaped model. Part II: new, accurate semi-analytical benchmarks for an impermeable solid. [PDF]

Meccanica, 2018
Peck D, Wrobel M, Perkowska M, Mishuris G.   +3 more
europepmc   +1 more source

Lightweight Sheet Molding Compound Composites With Enhanced Mechanical Performance via Cellulose Nanocrystal Reinforcement

Polymer Composites, EarlyView.
Mechanical Property Enhancement and 21% Density Reduction in CNC‐Reinforced Glass Fiber Composites. ABSTRACT The use of cellulose nanocrystals (CNCs) as a sustainable, high‐performance alternative to partially replace calcium carbonate (CaCO3) in polyester sheet molding compound (SMC) composites is investigated.
Kim Anh Pham, Shristi Ghosh, Andrew Geda, Kyriaki Kalaitzidou   +3 more
wiley   +1 more source

Simulation of Full-Area Propped Fracture Propagation and Productivity in Shale Gas Reservoirs. [PDF]

ACS Omega
Yu X, Chen K, Wang C, Zhu X, Sui G.
europepmc   +1 more source

Behavior of a Novel Cyclic Olefin‐Based Hot‐Melt Adhesive in CFRP Adhesive Joints Compared to Conventional Epoxy‐Based Structural Adhesives

Polymer Composites, EarlyView.
Rate‐dependent performance of composite adhesive joints using thermoset and thermoplastic adhesives, in terms of toughness and fatigue behaviour. ABSTRACT A recently developed hot‐melt adhesive (HMA) based on cyclic olefin chemistry, supplied as a transparent, non‐tacky thermoplastic film with a distinctive polymer microstructure, was evaluated in this
Hossein Malekinejad, Ricardo J. C. Carbas, Eduardo A. S. Marques, Lucas F. M. da Silva   +3 more
wiley   +1 more source

Study on vibration characteristics of roadheader cutting pre-cracked hard rock. [PDF]

Sci Rep
Liu H, Li F, He J, Wang W, Zhang H.
europepmc   +1 more source

Implicit level set algorithms for modelling hydraulic fracture propagation. [PDF]

Philos Trans A Math Phys Eng Sci, 2016
Peirce A.
europepmc   +1 more source