Results 41 to 50 of about 64,449 (218)

Experimental Study on Wave Characteristics of Stilling Basin with a Negative Step

Entropy, 2022
Stilling basin with a negative step is an important structure in hydraulic systems, because it can avoid atomization and decrease scouring problems.
Guibing Huang, Mingjun Diao, Lei Jiang, Chuan’ai Wang, Wang Jia   +4 more
doaj   +1 more source

Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A

Advanced Engineering Materials, EarlyView.
The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han, Julian M. Rosalie, Jan Radners, Mauro Madia, Philipp von Hartrott, Birgit Skrotzki   +5 more
wiley   +1 more source

Evaluation of Plasticity and Creep Parameters From Tensile Stress–Strain Data for a Range of Strain Rates

Advanced Engineering Materials, EarlyView.
This plot compares experimental tensile stress–strain curves (with 4 different strain rates) and corresponding modelled curves (obtained using the optimised sets of Voce and Miller–Norton parameter values shown). The inferred M‐N values, characterizing the creep, are very similar to those obtained via conventional creep testing.
S. Ooi, R. P. Thompson, T. W. Clyne
wiley   +1 more source

Direct Metal Deposition of Graphene–Ti28Nb35.4Zr Matrix Composites With Enhanced Mechanical, Corrosion, and Biocompatibility Properties for Bone Implants

Advanced Engineering Materials, EarlyView.
Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir, Jixing Lin, Yuncang Li, Li Zhu, Paul F. A. Wright, Cuie Wen   +5 more
wiley   +1 more source

Effect of debris accumulation on scour evolution at bridge pier in bank proximity

Journal of Hydrology and Hydromechanics, 2021
Large debris transported by flood affects scour features at bridge piers and increases the risks of structural failure. Geometric characteristics of the debris and the relative position of the pier with respect to the river bank are important parameters ...
Palermo Michele, Pagliara Simone, Roy Deep   +2 more
doaj   +1 more source

Compatibility of Methacrylate Based Resins Controls Interfacial Failure and Toughness in 3D‐Printed Multimaterial Composites

Advanced Engineering Materials, EarlyView.
This work shows that the mechanical performance of multimaterial digital light processing (DLP) printed thermoset composites is governed by resin compatibility and interfacial design rather than spatial patterning alone. Brittle and ductile resin combinations produced premature interfacial failure, while graded interfaces and mechanically compatible ...
Ahmed M. H. Ibrahim, Li Meng, Ahmad R. Najafi, Nicolas J. Alvarez   +3 more
wiley   +1 more source

A model for estimating the hydraulic conductivity of bentonite under various density conditions

Hydrology Research, 2022
Bentonite is an important material for low-permeability engineering systems used in dams and hazardous waste facilities. While models to characterize the hydraulic conductivity of bentonite have been developed in previous studies, these models were not ...
Tatsuya Kijima, Tsuyoshi Sasagawa, Takuma Sawaguchi, Norikazu Yamada   +3 more
doaj   +1 more source

Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading

Advanced Engineering Materials, EarlyView.
This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev, Noah‐Lean Roschlaub, Anne Jung   +2 more
wiley   +1 more source

Influence of Si Content and Milling Duration on the Microstructure and Mechanical–Tribological Properties of AlCoCrFeNiSi High‐Entropy Alloys

Advanced Engineering Materials, EarlyView.
Si‐doped AlCoCrFeNi high‐entropy alloys are synthesized by mechanical alloying to reveal the effect of Si content and milling time on phase evolution, microstructural refinement, and tribological behavior. A transition from FCC to BCC structure, significant grain refinement, and enhanced hardness and wear resistance are achieved, with the 4 at% Si ...
Mustafa Okumuş, Mehmet Emin Demir, Sercan Özpınar   +2 more
wiley   +1 more source

Estimation of river discharge using Monte Carlo simulations and a 1D hydraulic model based on the artificial multi-segmented rating curves at the confluence of two rivers

Environmental Research Communications
During extreme floods caused by climate change, reliable flow discharge data are essential for successful reservoir operation to mitigate downstream flood damage.
Hansol Kang, Yeonsu Kim, Hyunuk An, Jisun Byun, Joonwoo Noh   +4 more
doaj   +1 more source