The Influence of the form Error after Rotor Manufacturing on the Output Characteristics of an Orbital Hydraulic Motor [PDF]
, 2018 The technology of rotors manufacturing for orbital hydraulic motors causes a certain form error of the gear surface. This leads to oscillations of the diametrical gap between the rotors.
Panchenko, Anatolii +14 more
core
Rapid Fabrication of Self‐Propelled and Steerable Magnetic Microcatheters for Precision Medicine
Advanced Materials, EarlyView.A rapid Joule heating fabrication method for the production of self‐propelling, adaptive microcatheters, with tunable stiffness and integrated microfluidic channels is presented. Demonstrated through three microrobotic designs, including a steerable guiding catheter, an untethered wave‐crawling TubeBot, and a distal‐end propelled microcatheter, it was ...
Zhi Chen +5 more
wiley +1 more source
Experimental Studies on the Friction of Mobile Elements in Hydraulic Equipment
Scientific Bulletin of Valahia University: Materials and MechanicsIn this study we will focus on the problems that arise due to the high travel speeds that the piston of a hydraulic motor develops during operation. These speeds lead to an increase in the value of the kinetic friction coefficient.
Despa Veronica +2 more
doaj +1 more source
Modeling and Control of a 600 kW Closed Hydraulic Wind Turbine with an Energy Storage System
Applied Sciences, 2018 In this paper, an innovative closed hydraulic wind turbine with an energy storage system is proposed. The hydraulic wind turbine consists of the wind rotor, the variable pump, the hydraulic bladder accumulator, the variable motor, and the synchronous ...
Liejiang Wei +4 more
doaj +1 more source
The Dynamic Model of Plane Mechanism with Variable Ratio. [PDF]
, 2016 The paper contains the proposal how to reduce many–elements plane mechanism with one degree of freedom to chosen axis or line as one–element model of mechanism.
Cink, Jacek, Kosucki, Andrzej
core
Paraplegic standing supported by FES-controlled ankle stiffness [PDF]
, 2001 The objective of this paper was to investigate whether a paraplegic subject-is able to maintain balance during standing by means of voluntary and reflex activity of the upper body while being supported by closed loop controlled ankle stiffness using FES.
Hunt, K.J., Jaime, R.P., Matjacic, Z.
core +1 more source
Advanced Materials, EarlyView.This study reports the fabrication of MRI‐compatible elastomeric micro‐balloons via a multi‐step bubble casting process, where the monolithic elastomeric wall is selectively stiffened for reversible and controlled inflation and elasticity, depending on the target vessels for graded occlusion of cerebral arteries.
Jong Bin Kim +10 more
wiley +1 more source
The 25 kWe solar thermal Stirling hydraulic engine system: Conceptual design [PDF]
The conceptual design and analysis of a solar thermal free-piston Stirling hydraulic engine system designed to deliver 25 kWe when coupled to a 11 meter test bed concentrator is documented.
Emigh, Grant +4 more
core +1 more source
Design of a wrist and operator interface for an agricultural manipulator : a thesis presented in partial fulfilment of the requirements for the degree of Master of Technology in Engineering and Automation at Massey University [PDF]
, 2000 Roadside mowing and tree pruning has always been a job that most people would consider as unpleasant. This project is concerned with the development of a system to make these tasks simpler, safer and more pleasant for the operator.
Noaro, Adrian Peter Charles
core
Advanced Materials, EarlyView.An Aloe‐pinspired droplet electricity generator (A‐DEG) overcomes the limited energy collection zone of conventional DEGs by guiding impact droplets through a channeling midrib and artificial cuticle. The channeling midrib induces uni‐directional droplet spreading, while the artificial cuticle on the midrib further reinforces this behavior through its ...
Gibeom Lee +8 more
wiley +1 more source