Results 11 to 20 of about 3,922,021 (231)
TENDENCIES AND PROSPECTS OF APPLICATION OF HYDROSTATIC-MECHANICAL TRANSMISSION IN CAR- AND TRACTORBUILDING [PDF]
Avtomobilʹnyj Transport (Harʹkov), 2012 Research of advantages and lacks of hydrostatic-mechanical transmission, application of hydrostatic-mechanical transmission, expedience of the use of hydrostatic-mechanical transmission on motor transport and agricultural machines have been done.
V. Samorodov, A. Bondarenko
doaj +5 more sources
PERSPECTIVE HYDROSTATIC-MECHANICAL TRANSMISSIONS FOR WHEELED TRACTORS OF AGRICULTURAL SETTING [PDF]
Avtomobilʹnyj Transport (Harʹkov), 2013 The kinematics charts of perspective hydrostatic-mechanical transmission are presented, their basic structural parameters, the size of hydraulic machines of hydrostatic transmission are identified, the kinematic and power parameters of transmissions are ...
Samorodov, V., Bondarenko, A.
doaj +7 more sources
Stacking Pressure-Driven Interfacial Dynamics in Anode-Free Solid-State Lithium Batteries. [PDF]
Adv Sci (Weinh)Using a three‐electrode setup, it is found that stacking pressure improves both anode and cathode interfaces but more effectively stabilizes the anode. Under low pressure, a sudden anode resistance rise indicates contact loss. Higher pressure delays this via Li creep and plastic deformation, maintaining interfacial contact.
Liang J +8 more
europepmc +2 more sources
Advanced Bearing System for Ultra Precision Plastic Electronics Production Systems [PDF]
, 2014 The aims of this MSc research project are to investigate the application of aluminium for the main components of an ultra-precision spindle defined for use in R2R production systems and to produce a reel to reel rotary aluminium hydrostatic bearing ...
Zhao, Gang
core +7 more sources
Bulletin of the National Technical University «KhPI». Series: Automobile and Tractor Construction, 2022 The paper considers ways to increase the efficiency of two-stream hydrovolume-mechanical transmissions (GOMT) of vehicles through the rational choice of transmission mode and the introduction into the design of the recovery system of circulating parasitic power of the closed circuit.
openaire +3 more sources
Hydrostatic compression on polypropylene foam [PDF]
, 2008 Models currently used to simulate the impact behaviour of polymeric foam at high strain rates use data from mechanical tests. Uniaxial compression is the most common mechanical test used, but the results from this test alone are insufficient to ...
VIOT, Philippe
core +1 more source
Modeling and characterization of a low power hydro-mechanical transmission with comparisons to a hydrostatic transmission [PDF]
, 2005 Hydro-mechanical transmissions attempt to balance the productivity increases of hydrostatic transmissions with the higher efficiencies of mechanical transmissions.
Romans, Kurt
core +1 more source
Energies, 2022 Dynamometers are used to evaluate the real-world performances of drivetrains in various loading conditions. Due to its superior power density, high bandwidth, and design flexibility, a hydrostatic power-regenerative dynamometer is an ideal candidate for ...
Biswaranjan Mohanty, Kim A. Stelson
doaj +1 more source
The influence of hydrostatic pressure on the interlaminar fracture toughness of carbon/epoxy composites [PDF]
, 2006 The use of composites for deep sea applications requires a thorough understanding of the behaviour of these materials. While several studies have examined the influence of pressure on in-plane properties few data are available for the interlaminar ...
Peleau, M. +3 more
core +1 more source
Controlled porosity alumina structures for ultra-precision hydrostatic journal bearings [PDF]
, 2010 A series of fine-grade alumina powders has been used in combination with maize starch granules to produce porous structures for porous hydrostatic journal- bearing applications. A comprehensive series of tests was conducted to characterize porosity in
John Corbett +6 more
core +1 more source