Results 31 to 40 of about 6,258 (242)

Advanced Electron Microscopy and Microcomputed Tomography Analysis of Single‐Crystal Ni‐Base Superalloys After Short‐Term Multiaxial Creep

Advanced Engineering Materials, EarlyView.
This work studies the anisotropic behavior of circular notched tensile specimens of Ni‐base superalloy single crystals during high‐temperature tensile creep along [001], [110], and [111]. Correlative scale‐bridging imaging of specimens reveals early rupture along [110] because 1) plastic deformation proceeds faster at notch center; 2) more (brittle ...
Leonardo Agudo Jácome, Lijie Cao, Christoph Somsen, Johannes Boes, René Hesse, Werner Theisen, Gunther Eggeler   +6 more
wiley   +1 more source

CALCULATION OF COMBINED HYDROSTATIC BEARINGS OF DOUBLE TYPE AT STATIONARY EXTERNAL LOAD

Авіаційно-космічна техніка та технологія, 2017
The relevance of the application of combined hydrostatic bearings of the twin type in various units and power plants is shown, the loads in which reach ten tons.
Владимир Иосифович Назин
doaj   +1 more source

Extrusion‐Based Additive Manufacturing of Advanced Ceramics: Strengthening Mechanisms and Process Optimization Review

Advanced Engineering Materials, EarlyView.
This review comprehensively evaluates extrusion‐based additive manufacturing for advanced ceramics, detailing feedstock options and key process parameters. By critically addressing defect mechanisms like porosity and cracking, the work highlights optimization strategies through machine learning and advanced postprocessing.
Meisam Bakhtiari, Mohammad Hadi Sheikh‐Ansari, Avinash Borgaonkar, Mehran Dadkhah, Abdollah Saboori   +4 more
wiley   +1 more source

ANALYSIS OF BEARING PERFORMANCE OF HYDRODYNAMIC AND HYDROSTATIC BALL BEARINGS UNDER INTERFACE SLIP BASED ON ORIFICE THROTTLING

Jixie qiangdu, 2022
Due to study the influence of interfacial slip on the bearing capacity of hydrostatic and hydrostatic ball bearings with small orifice throttling, the Reynolds equation of ball bearings considering interfacial slip was established based on the linear ...
ZHOU YiHao, SHEN JingFeng, CHEN YuFei
doaj  

Cellular Responses to Mechanical Cues Across Scales: From Fundamental Insights to Translational Potential

Advanced Healthcare Materials, EarlyView.
This review examines how cellular behavior is regulated by mechanical cues transmitted through soft biomaterials, from single‐cell mechanosensing to tissue‐level adaptation. It highlights why physiological relevance, rather than model complexity alone, is critical for translational mechanobiology and introduces a scoring framework linking material ...
Mathias Polz, Manuel P. Kainz, Niklas Haider, Theresa Rienmüller, Kerstin Lenk, Rupert Kargl, Michele Terzano, Gerhard Sommer, Gerhard A. Holzapfel, Julia Fuchs   +9 more
wiley   +1 more source

Hydrostatic Asymmetric Journal Gas Bearings for Largely Unbalanced Rotors of Seismic ACROSS Transmitters

Journal of Advanced Mechanical Design, Systems, and Manufacturing, 2007
In currently working seismic ACROSS (Accurately Controlled Routinely Operated Signal System) transmitters, an unbalanced rotor with large eccentric mass, which generates elastic waves, is supported by roller bearings.
Tomohiko ISE, Takao TORII, Nobuyoshi MORITA, Shinichi TOGO, Makoto OKANO   +4 more
doaj   +1 more source

Inhibition of VEGF‐Induced Angiogenesis and Vascular Leakage by Bicistronic Co‐Expression of Aflibercept and COMP‐Ang1

Advanced Healthcare Materials, EarlyView.
A bicistronic rAAV8 vector encoding Aflibercept (Afb) and COMP‐cAng1 simultaneously coordinates VEGF clearance and Tie2‐mediated vessel maturation. In a 3D angiogenesis‐on‐a‐chip model, rAAV8‐Afb/cAng1 effectively reverses pathological barrier breakdown under clinical disease‐mimicking challenges.
Bong‐Kyu Kim, Jaehong Min, Sang‐Hee Park, Subeen Shin, Sangbin Yu, Jeong‐Eun Park, Sujin Kim, Wooju Park, Jihoon Ko, Sunjong Kwon   +9 more
wiley   +1 more source

Tough, Ductile, and Strong Hard‐Soft Cementitious Composite Enabled by Multi‐Material Additive Manufacturing

Advanced Materials, EarlyView.
Drawing inspiration from the layered hard‐soft architecture found in sea sponges, this work establishes a new framework for architected cementitious composites (ACC) through multi‐material additive manufacturing (MMAM) process. The integration of mortar and elastomer phases into layered architectures enables synergistic toughening mechanisms, including
Aimane Najmeddine, Shashank Gupta, William Makinen, Zayvinn Lin, Krystal Delnoce, Reza Moini   +5 more
wiley   +1 more source

Analysis of Hydrostatic Bearing Structure Characteristics of Guide Sleeve of Electro hydraulic Servo Cylinder

Journal of Harbin University of Science and Technology, 2020
As a typical bionic foot walking robot, hydraulic quadruped robot has attracted much attention due to its high mobility, strong load capacity and smooth motion The electrohydraulic servo cylinder, as its power actuating element, requires low friction ...
SHAO Jun peng, LI Jing bo, SUN Gui tao
doaj   +1 more source

Phase Engineering of Nanomaterials (PEN): Evolution, Current Challenges, and Future Opportunities

Advanced Materials, EarlyView.
This review summarizes the synthesis, phase transition, advanced characterization spanning ex situ to in situ and operando techniques, and diverse applications of phase engineering of nanomaterials (PEN). It further outlines key challenges and future opportunities, such as phase stability, architecture control, and artificial intelligence (AI)‐driven ...
Ye Chen, Zhanxi Fan, Jingjie Ge, Qiyuan He, Zhuangchai Lai, Jiawei Liu, Chaoliang Tan, Hua Zhang   +7 more
wiley   +1 more source