Results 61 to 70 of about 125,813 (262)

Miniaturized Hyper-Redundant Manipulator Using Multi-Cable for Minimally Invasive Surgery

IEEE Access
Minimally invasive surgery (MIS) using robots minimizes patient injury but is challenging due to reduced bending force in smaller-diameter tools. Lowering the bending resistance of actuating cables is critical, particularly when tool diameters are small ...
Jaehyung Yoo, Daeyun Jang, Chunwoo Kim, Seungbeum Suh, Jeongryul Kim   +4 more
doaj   +1 more source

Formation and Investigation of Electrospun Eudragit E100/Oregano Mats

Molecules, 2019
An electrospun mat of Eudragit E100 (EE100) (a cationic copolymer based on dimethylaminoethyl methacrylate, butyl methacrylate, and methyl methacrylate) was used as a delivery system for oregano ethanolic extract (OEE).
Juste Baranauskaite, Erika Adomavičiūtė, Virginija Jankauskaitė, Mindaugas Marksa, Zita Barsteigienė, Jurga Bernatoniene   +5 more
doaj   +1 more source

Precipitation Simulations of the O‐Phase in Ti2AlNb Alloys Processed by Laser Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
Simulated and experimental evolution of the O‐phase volume fraction during postprocessing of a Ti‐21Al‐25Nb (at.%) alloy processed by laser powder bed fusion. With results of sensitivity to input parameters from a thorough and quantified analysis, the interfacial energy matrix/precipitate is the most relevant input parameter for the simulation of the O‐
Silvana Tumminello, Joachim Gussone, Suzana G. Fries, Marcus Rackel, Andreas Stark, Norbert Schell, Jan Haubrich, Guillermo Requena   +7 more
wiley   +1 more source

Investigation of the Influence of Local Low Strength Concrete on the Bearing Capacity of Bending Reinforced Concrete Beams

Железобетонные конструкции
Reinforced concrete beams can experience local low concrete strength under certain conditions, for example, poor construction practices can cause problems such as concrete voids, surface cavities, block cracking, surface sinks and create areas of low ...
A. G. Tamrazyan
doaj   +1 more source

Compatibility of Methacrylate Based Resins Controls Interfacial Failure and Toughness in 3D‐Printed Multimaterial Composites

Advanced Engineering Materials, EarlyView.
This work shows that the mechanical performance of multimaterial digital light processing (DLP) printed thermoset composites is governed by resin compatibility and interfacial design rather than spatial patterning alone. Brittle and ductile resin combinations produced premature interfacial failure, while graded interfaces and mechanically compatible ...
Ahmed M. H. Ibrahim, Li Meng, Ahmad R. Najafi, Nicolas J. Alvarez   +3 more
wiley   +1 more source

Laser‐Induced Graphene from Waste Almond Shells

Advanced Functional Materials, EarlyView.
Almond shells, an abundant agricultural by‐product, are repurposed to create a fully bioderived almond shell/chitosan composite (ASC) degradable in soil. ASC is converted into laser‐induced graphene (LIG) by laser scribing and proposed as a substrate for transient electronics.
Yulia Steksova, Anna Chiara Bressi, Marina Galliani, Attilio Marino, Gianni Ciofani, Eduardo Machado‐Charry, Hilda Gomez Bernal, Alessandra Francini, Luca Sebastiani, Francesco Greco   +9 more
wiley   +1 more source

Experimental and modelling investigation of the deformation, drag and break-up of drizzle droplets subjected to strong aerodynamics forces in relation to SLD aircraft icing [PDF]

, 2005
The distortion, drag and break-up of drizzle droplets subjected to strong aerodynamic forces was investigated to understand the pre-impact behaviour of droplets in aircraft icing from supercooled freezing drizzle.
Luxford, Geoffrey
core  

Composites of Shellac and Silver Nanowires as Flexible, Biobased, and Corrosion‐Resistant Transparent Conductive Electrodes

Advanced Functional Materials, EarlyView.
Shellac, a centuries‐old natural resin, is reimagined as a green material for flexible electronics. When combined with silver nanowires, shellac films deliver transparency, conductivity, and stability against humidity. These results position shellac as a sustainable alternative to synthetic polymers for transparent conductors in next‐generation ...
Rahaf Nafez Hussein, Tiago Carneiro Gomes, Eliza Ng, Simon Rondeau‐Gagné, Tricia Breen Carmichael   +4 more
wiley   +1 more source

Hot‐Film and Calorimetric Methods With Transient Heating for Measurement of High Biofluid Flow Rate

Advanced Functional Materials, EarlyView.
Accurate measurement of biofluid flow rate is vital for clinical diagnostics. We propose a transient heating strategy using short thermal pulses and peak temperature tracking to enhance the flow sensitivity of the hot‐Film and calorimetric methods. Simulations show how optimal heating time maximizes sensitivity across flow rates.
Yuanting Wei, Shupeng Li, Kyung Rok Pyun, Tianyu Yang, Bosung Kim, Haotian Yang, John A. Rogers, Yonggang Huang, Haohui Zhang   +8 more
wiley   +1 more source

Lattice of superconducting multilayer nanotubes as ideal high-temperature superconductor

, 2000
Combining Little's and Ginzburg's ideas with recent progress in nanotubes research, a novel type of material is advanced as a perspective high-Tc superconductor on base of a close-packed lattice of quasi-1D superconducting nanotubes. Idea is offered that
Pokropivny, V.V., Pokropivny, A.V., Makarov, I. M.   +2 more
core