Results 131 to 140 of about 548,380 (268)

On the Lightweight Potential of Laser Additive Manufactured NiTi Triply Periodic Minimal Sheet Lattices

Advanced Engineering Materials, EarlyView.
This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo, Shuo Qu, Shiming Gao, Xu Song   +3 more
wiley   +1 more source

Three filters for the enhancement of the images acquired from fluorescence microscope and weak-light-sources and the image compression. [PDF]

Heliyon, 2023
Jia M, Xu J, Yang R, Li Z, Zhang L, Wu Y.   +5 more
europepmc   +1 more source

The Impact of High‐Productivity Processing on the Fatigue Failure of an Additive Manufactured Superalloy HAYNES 282

Advanced Engineering Materials, EarlyView.
The low cycle fatigue life of additive manufactured HAYNES® 282® superalloy was investigated for conventional and high‐productivity processing: samples of the former lasted 1400–1700 cycles, while samples of the latter failed at ~ 1200 cycles, at 760 °C and 1% strain.
Abdul Shaafi Shaikh, Ahmed Fardan, Tatiana Mishurova, Eduard Hryha   +3 more
wiley   +1 more source

Retracted: Manta Ray Foraging Optimization with Vector Quantization Based Microarray Image Compression Technique. [PDF]

Comput Intell Neurosci, 2023
Intelligence And Neuroscience C.
europepmc   +1 more source

Laser Powder Bed Fusion of Copper–Tungsten Composites for Heat Sink Applications in High‐Power Electronics

Advanced Engineering Materials, EarlyView.
This article demonstrates the successful qualification of a copper–tungsten composite for laser powder bed fusion. The resulting components exhibited high density, high thermal conductivity, and reduced thermal expansion. Heat sinks with complex geometries were successfully manufactured, clearly showcasing the material's potential for additive ...
Simon Rauh, Shashank Deepak Prabhu, Jannik Huber, Lioba Fischer, Gerhard Wolf, Nico Hempel, Peter Mayr   +6 more
wiley   +1 more source

Patched-Based Swin Transformer Hyperprior for Learned Image Compression. [PDF]

J Imaging
Buthelezi SB, Tapamo JR.
europepmc   +1 more source

Geometry-aware view reconstruction network for light field image compression. [PDF]

Sci Rep, 2022
Zhang Y, Wan L, Mao Y, Huang X, Liu D.
europepmc   +1 more source

Facilitating Expedited Drug Approval– the Past, Present, and Future of Clinical Trials for Pediatric Rheumatic Disease

Arthritis Care &Research, Accepted Article.
Pamela F. Weiss, Hermine I. Brunner
wiley   +1 more source

Duplex Stainless Steel Laser‐Surface Textured: Stability in Brine Solution

Advanced Engineering Materials, EarlyView.
Controlled laser‐surface treatment (LST) of duplex DSS2205 steel is performed to increase its stability in brine solution under cyclic electrochemical assays. The superior protection with respect to flat and smooth panels is attributed to the presence of FeCr2O4 as the main protective oxide layer in the LST surface, after corrosion tests. The stability
Mohammad Rezayat, Hamidreza Enshaei, Elaine Armelin, José I. Iribarren, Antonio Mateo, Miguel Morales   +5 more
wiley   +1 more source

An image compression-encryption algorithm based on BP neural network optimized with fireworks algorithm. [PDF]

Sci Rep
Liang Y, Peng B, Liu R, Kang N, Zhou H.
europepmc   +1 more source