Results 171 to 180 of about 1,177,243 (298)

Three Dimensional Imaging [PDF]

, 2020
openaire   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

3D-Assisted Scapular Fracture Fixation in a Polytraumatized Patient: A Case Report. [PDF]

J Orthop Case Rep
Dobrich J, Deegan MK, Gerber CD, Min KS.
europepmc   +1 more source

Tribological Performance of 60NiTi Alloy Under Varying Contact Conditions and Elevated Temperatures in Linear Reciprocating Sliding

Advanced Engineering Materials, EarlyView.
This study investigates the tribological response of 60NiTi alloy under dry, water‐lubricated and high‐temperature conditions. The alloy exhibits decreasing wear volume and friction with increasing temperature due to the formation of protective oxide layers. The work clarifies dominant wear mechanisms and demonstrates the suitability of 60NiTi for high‐
Anthony Onyebuchi Okoani, Miguel Angel Selles, Maziar Ramezani   +2 more
wiley   +1 more source

T2 weighted three dimensional imaging of the whole heart

Journal of Cardiovascular Magnetic Resonance, 2009
Simonetti Orlando P, Chung Yiu-Cho, Jerecic Renate   +2 more
doaj   +1 more source

Characterization of Nitinol Produced by Laser Powder Bed Fusion for Mechanical Metamaterial Applications

Advanced Engineering Materials, EarlyView.
Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek, Jakub Hurník, Miroslav Šmíd, Ondřej Zobač, Melanie Todt, Daniel Koutný   +5 more
wiley   +1 more source

Exploring Competency Development Through Simulation-Based Preclinical Training in Veterinary Education. [PDF]

Vet Sci
Galarza-Alvarado P, Moya-Loaiza DP, Ramonet F, Vázquez-Albornoz JH, Moncayo-Matute FP.   +4 more
europepmc   +1 more source

Three-dimensional imaging and three-dimensional coordinate gathering in three-dimensional optical micromanipulation system [PDF]

, 2008
Dam, Jeppe Seidelin, Glückstad, Jesper, Palima, Darwin, Perch-Nielsen, Ivan R.   +3 more
core  

EBSD Study of Creep‐Induced Lattice Misorientation in MgO‐Particle‐Reinforced Austenitic Steel Composites

Advanced Engineering Materials, EarlyView.
Creep experiments at 900°C on coarse‐grained steel‐ceramic composites containing recycled magnesia reveal that higher ceramic volume fractions significantly enhance the creep resistance. Detailed EBSD investigations identify subgrain formation in the steel matrix as the dominant deformation mechanism.
Moritz Müller, Amaya Compart, Mahnaz Mehdizadehlima, Serhii Yaroshevskyi, Christos G. Aneziris, Horst Biermann, Anja Weidner   +6 more
wiley   +1 more source

Cinematic Rendering in Preoperative Evaluation of Primary Tibial Leiomyosarcoma. [PDF]

Radiol Imaging Cancer
Zhou X, Zhao ZL, Huang C.
europepmc   +1 more source