Results 51 to 60 of about 1,138,382 (329)
Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6
Advanced Engineering Materials, EarlyView.The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter +4 more
wiley +1 more source
EnergiesElectric vehicles are increasingly seen as a viable alternative to conventional combustion-engine vehicles, offering advantages such as lower emissions and enhanced energy efficiency.
Sara El Afia +3 more
doaj +1 more source
Can Ti‐Based MXenes Serve as Solid Lubricants for Brake Applications? A Tribological Study
Advanced Engineering Materials, EarlyView.This study explores the first implementation of Ti‐based MXenes materials in brake pad friction composite material. The resulting composite material exhibits a 48% reduction in the wear rate; alongside significant improvements are observed for thermal and mechanical properties.
Eslam Mahmoud +7 more
wiley +1 more source
Simulation Study on the Single-Phase Immersion Cooling Performance of Lithium-Ion Battery Packs
Applied SciencesWith the continuous development and innovation of thermal management technology for lithium-ion batteries, the advantages of direct immersion liquid cooling technology have become increasingly prominent.
Jiajun Hu +5 more
doaj +1 more source
Investigations into the coefficient of thermal expansion of porous films prepared on AA7175 T7351 by anodizing in sulphuric acid electrolyte [PDF]
, 2010 The aim of this study was to investigate the Coefficient of Thermal Expansion (CTE) of anodic films on 7175 T7351 aluminium alloy and to evaluate the influence of the film characteristics on this value.
Arurault, Laurent +5 more
core +3 more sources
Advanced Engineering Materials, EarlyView.High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé +5 more
wiley +1 more source
The immersion cooling technology: Current and future development in energy saving
Alexandria Engineering Journal, 2022 The world's energy consumption shows an increasing trend. Unfortunately, it is still dominated by the use of fossil energy. This condition results in concerns that an energy crisis will occur due to running out of non-renewable energy and an ...
Nugroho Agung Pambudi +5 more
doaj +1 more source
Damage assessment of concrete structures exposed to fire [PDF]
, 2013 During a fire, concrete structures behave in most cases very well. It could therefore be of economic interest to repair the damaged structures, as costs for demolition and rebuilding can be avoided and the building can be reused faster.
Annerel, Emmanuel, Taerwe, Luc
core +1 more source
Advanced Engineering Materials, EarlyView.Bimetallic (NiFe) and trimetallic (NiFeCr) nanoalloys (NAs) are synthesized using corresponding oxide mixtures using microwave hydrogen plasma within a few milliseconds. The process simultaneously 1) reduces metal oxides to metals; 2) downsizes the particles from micrometers to nanometers; and 3) blends the metals to form NAs.
Sachin Kumar +5 more
wiley +1 more source
Testing methodologies for corrosion fatigue [PDF]
, 2015 Offshore constructions are subjected to cyclic loading conditions. This situation is combined with the corrosive nature of the surrounding environment. It is of actual concern whether the combined effect is more damaging or not than the superposition of ...
De Waele, Wim +2 more
core +1 more source