Results 161 to 170 of about 3,494 (261)

Socio‐Economic and Ecological Drivers of the Spread of Non‐Native Tilapia (Oreochromis niloticus) Species in Kenya

Aquaculture, Fish and Fisheries, Volume 6, Issue 5, October 2026.
ABSTRACT Nile tilapia (Oreochromis niloticus) is the dominant non‐native fish species in Kenya's inland waters, but its spread reflects a coupled socioecological process rather than a simple biological invasion. This review examines the socio‐economic, governance and ecological drivers of its expansion within a socioecological systems and invasion ...
Otieno Kashim Oginga, Robert Maina Waruiru, Finnan Okoth Ageng'o, Callen Onura, Caroline Jepkorir Kibet   +4 more
wiley   +1 more source

Complex crater formation by low energy impactors. [PDF]

PLoS One
Tardini Paulino R, Oblesrczuk T, Lencioni Aliboni J, Hetem Junior A, Schoenmaker J.   +4 more
europepmc   +1 more source

Laser Surface Treatment of Nickel‐Alumina Coating for Enhancement of Erosion and Corrosion Resistance of High Speed Steel Vanes

Applied Research, Volume 5, Issue 5, October 2026.
Laser surface treatment was carried out to enhance the performance of Ni‐Al2O3 coatings on HSS substrates. The results revealed improved microstructural features, corrosion resistance and significant reduction in slurry erosion wear with 18 W laser treatment. ABSTRACT The sliding wear between hydraulic vane tip and the inner surface of the cam ring can
Majunath Keshav, Achutarao Bharatish, Sivakumar Solaiachari, Srilatha Rao   +3 more
wiley   +1 more source

Optimized Sodium-Enhanced MALDI-2 Enables Multimodal Imaging of Triacylglycerols. [PDF]

J Am Soc Mass Spectrom
Molloy KR, Marshall CR, Dufresne M, Migas LG, Schrag MS, Van de Plas R, Spraggins JM.   +6 more
europepmc   +1 more source

Surface Characterization of Magnesium Alloy Machined by Wire Electrical Discharge Machining

Applied Research, Volume 5, Issue 5, October 2026.
WEDM parameters significantly influence the surface quality, machining efficiency, and microstructure of AZ31 magnesium alloy. Lower discharge energy produced a smoother surface, shorter machining time, and reduced voids and microcracks, demonstrating improved surface integrity and machining performance.
Muhammad Syafiq Iskandar Rosni, Muhammad Al'Hapis Abdul Razak, Farooq Azam, Turnad Lenggo Ginta, Muizuddin Azka, Sadaqat Ali, Haizum Aimi Zaharin, Abdul' Azeez A. Aliyu, Ahamad Zaki Mohamed Noor   +8 more
wiley   +1 more source

Machining behavior and phase transformation in WEDM of Ti₅₀Ni₄₉Co₁ shape memory alloy. [PDF]

Sci Rep
Soni H, Kumar RS, Kumaraswamy GN, Madhusudan M, Solaimuthu C, Verma R, Raj NA, Sharma P.   +7 more
europepmc   +1 more source

Toward a Standardized Classification of Surface Defects in the Coating and Drying Processes of Lithium‐Ion Battery Electrode Manufacturing

Batteries &Supercaps, Volume 9, Issue 10, October 2026.
Surface defects during coating and drying are a major cause of scrap in lithium‐ion battery production. Using digital optical microscopy, a multilayer catalog is developed that describes six defect classes with quantitative features such as size, depth, and wall angle.
Fabian Kux, Julian Wonneberger, Thomas Ackermann, Michael Przybylek, Alexander Mattern   +4 more
wiley   +1 more source

The origin of complex crater formation during high-speed impacts. [PDF]

Sci Adv
Celebi HF, Andrews AJ, Pothos I, Bellefeuille NA, Olson BA, Schwartzentruber TE, Hogan CJ.   +6 more
europepmc   +1 more source

Identification of Changes in Gene Expression

Biometrical Journal, Volume 68, Issue 5, October 2026.
ABSTRACT Evaluating the change in gene expression is a common goal in many research areas, such as in toxicological studies, which are particularly important in pre‐clinical research. In practice, the analysis is often based on multiple t‐tests evaluated at the observed time points of the experiment, which limits the accuracy of determining the precise
Lucia Ameis, Kathrin Möllenhoff
wiley   +1 more source

Magmatic origin of the Dewar magnetic anomaly: Implications for an early lunar dynamo. [PDF]

Sci Adv
Yang X, Mittelholz A, Broquet A, Moorkamp M.   +3 more
europepmc   +1 more source