Results 91 to 100 of about 1,013,684 (323)
Advanced Engineering Materials, EarlyView.Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth +6 more
wiley +1 more source
Grid Tie Inverter in Photovoltaic System for Residential Application [PDF]
, 2010 This paper presents a grid tie inverter (GTI) in photovoltaic, PV system for residential application. The proposed GTI will be switched with a combination switching strategy of square wave and the sinusoidal pulse width modulation, SPWM.
Tan, kheng kwang
core
Application of multiple resistive superconducting fault-current limiters for fast fault detection in highly interconnected distribution systems [PDF]
, 2013 Superconducting fault-current limiters (SFCLs) offer several benefits for electrical distribution systems, especially with increasing distributed generation and the requirements for better network reliability and efficiency.
Blair, Steven Macpherson +3 more
core +1 more source
, 2020 Infiltration is an effective way to improve the performance of the oxygen electrode for solid oxide cells (SOCs). Most studies on infiltrated SOCs are carried out on button cells with a small active area.
Xiaofeng Tong +4 more
semanticscholar +1 more source
Advanced Engineering Materials, EarlyView.This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Carbon‐free inert anodes are essential for decarbonizing aluminum electrolysis. This study investigates a recyclate‐based MgO‐316L steel composite anode tested under galvanostatic Hall–Héroult conditions in cryolite at 1000°C. Microstructural analysis reveals selective MgO fluorination, spinel and oxide layer formation, electrolyte infiltration, and ...
Serhii Yaroshevskyi +7 more
wiley +1 more source
AIM QuTE: Automated Impedance Metrology extending the Quantum Toolbox for Electricity
, 2013 The “Automated impedance metrology extending the quantum toolbox for electricity” project (AIM QuTE) will extend Josephson impedance bridges capabilities to the whole complex plane with the best level of uncertainties (0.05 ppm).
L. Palafox +13 more
semanticscholar +1 more source
Advanced Engineering Materials, EarlyView.The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert +6 more
wiley +1 more source
Technical and vocational skills (TVS): a means of preventing violence among youth in Nigeria [PDF]
, 2017 Technical and vocational skills are an important tool for reducing violence among youth, especially in Nigeria, who face security challenges due to different kinds of violence.
Ibrahim, Mohammed +1 more
core
Advanced Engineering Materials, EarlyView.This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff +9 more
wiley +1 more source