Results 111 to 120 of about 73,972 (294)

Additive Gaussian Process Regression for Predictive Design of High‐Performance, Printable Silicones

open access: yesAdvanced Engineering Materials, EarlyView.
A chemistry‐aware design framework for tuning printable polydimethylsiloxane (PDMS) for vat photopolymerization (VPP) is developed using additive Gaussian process (GP) modeling. Polymer network mechanics informs variable groupings, feasible formulation constraints, and interaction variables.
Roxana Carbonell   +3 more
wiley   +1 more source

Design of Π impedance matching networks [PDF]

open access: yesProceedings of IEEE International Symposium on Circuits and Systems - ISCAS '94, 2002
Yichuang Sun, J. Kel Fidler
openaire   +1 more source

Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics

open access: yesAdvanced Engineering Materials, EarlyView.
Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost   +4 more
wiley   +1 more source

Rafting of Ni‐Based Superalloys Under Multiaxial Load as Understood by Phase‐Field Simulations and Critical Experiments

open access: yesAdvanced Engineering Materials, EarlyView.
Phase‐field simulations coupled with dislocation‐density‐based crystal plasticity modeling reproduce γ′ rafting behavior in single‐crystal Ni‐based superalloys under varied loading conditions. The model captures both macroscopic creep and microscopic morphology evolution, with results matching high‐temperature creep experiments.
Micheal Younan   +5 more
wiley   +1 more source

Power transfer optimised automatic matching networks [PDF]

open access: yes
Matching networks are widely used to enhance active power transfer when radio frequency generators drive complex loads. The tuning of the network for varying loads typically involves searching for optimum matching conditions.
Glöckner, Reinhard Jörg
core  

Microstrip antennas [PDF]

open access: yes, 1973
It is possible to design and construct simple, efficient microwave antenna, either linearly or circularly polarized, which should be useful in phased arrays. Mounted on thin dielectric substrate, it extends slightly above ground plane.
Howell, J. Q.
core   +1 more source

Design of Impedance Matching Networks for RF Applications

open access: yesAsian Journal of Engineering and Technology, 2018
This technical paper presents a design and study of impedance matching for RF (radio frequency) circuit application of common-source amplifier topology.  Input and output matching networks of the amplifier were designed and computed ensuring unconditional stability.  Inductors and capacitors are key passive components that are crucial for impedance ...
openaire   +2 more sources

A Reconfigurable RF MEMS Triple Stub Impedance Matching Network

open access: yes2006 European Microwave Conference, 2006
This paper presents a reconfigurable triple stub impedance matching network using RF MEMS technology centered at 10GHz. The device is capable of covering impedances on the whole Smith Chart. The device structure consists of three variable length stubs which are designed as distributed MEMS transmission lines and two lambdag/8 length CPW transmission ...
Unlu, M.   +9 more
openaire   +2 more sources

Additive Manufacturing of Continuous Fibre Reinforced Composites: Process, Characterisation, Modelling, and Sustainability

open access: yesAdvanced Engineering Materials, EarlyView.
Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley   +1 more source

Phase Field Failure Modeling: Brittle‐Ductile Dual‐Phase Microstructures under Compressive Loading

open access: yesAdvanced Engineering Materials, EarlyView.
The approach by Amor and the approach by Miehe and Zhang for asymmetric damage behavior in the phase field method for fracture are compared regarding their fitness for microcrack‐based failure modeling. The comparison is performed for the case of a dual‐phase microstructure with a brittle and a ductile constituent.
Jakob Huber, Jan Torgersen, Ewald Werner
wiley   +1 more source

Home - About - Disclaimer - Privacy