CFD Modelling of Pump as Turbine with Various Number of Blade for Microhydro System
Pump as Turbine is an electromechanically component that is largely used in microhydro system. The main advantages of pump as turbine compared to commercially available turbines are lower cost, easier to maintain and readily available. These key features
Mohd Azlan Ismail Ismail +3 more
doaj +1 more source
Experience of applying 3D-scanning and CFD calculations to study and optimization the flow in the impeller of a multi-shaft centrifugal compressor [PDF]
The paper presents an analysis of semi-open centrifugal impellers of a three-stage multi-shaft compressor. A 3D-scanning of the geometry of the impellers is carried out, a CFD calculation is carried out at the design operating mode of the compressor ...
E. V. Filimonov +3 more
doaj +1 more source
A 57‐Year‐Old Male With Behavioral Variant Frontotemporal Dementia and MATR3 and NOS3 Mutations
ABSTRACT This report presents a case of behavioral variant frontotemporal dementia caused by mutations in the MATR3 and NOS3 genes, aiming to analyze its clinical manifestations and genetic characteristics. For a case presenting with personality changes and gait abnormalities as the initial symptoms, this study conducted a comprehensive analysis of its
Feifei Lin, Saie Huang
wiley +1 more source
Feasibility of Nitrogen as a Carrier Gas for Inconel Cold Spray in Hydropower Application
N2, despite being nearly two orders of magnitude cheaper than He, is a feasible carrier gas for cold spray Inconel coatings in hydropower repair applications when higher gas temperature and pressure are used. Reducing powder size significantly improved cavitation resistance, while the addition of fine chromium carbide particles further enhanced erosion
Tianhao Wang +4 more
wiley +1 more source
Energy transfer process and evolution characteristics in impeller of contra-rotating axial fan
Energy is transferred to the airflow during the rotation of impeller. In engineering, the efficient energy conversion is a key issue. Mastering the energy transfer process in impeller is the premise and basis for realizing efficient energy conversion. In
Yongping CHEN +5 more
doaj +1 more source
Deep Learning-assisted Fluid–structure Interaction for Fatigue Life Analysis of Slurry Pump Impellers in Particulate Two-phase Flow [PDF]
Slurry pump impellers operating in particulate solid–liquid flows often experience stress concentration and fatigue failure, limiting their reliability and service life.
Z. Liu, K. Peng, X. Lv, H. Chen, Z. Qu
doaj +1 more source
The flow characteristics at a centrifugal pump impeller are significantly affected by the hub inclination angle (HIA). The large eddy simulation turbulence model is employed to simulate the centrifugal pump impeller internal flow at two HIA values under ...
Renfei Kuang +3 more
doaj +1 more source
Fully 3D‐Printed Wave‐Wound Electromagnetic Motors
This work presents the first fully 3D‐printed wave‐wound electromagnetic motors, which are created using conductive nanoparticle inks, carbon‐filled nylon polymers, and surface mount components. These motors can achieve a stall torque of 7.62N·mmA−1$7.62 \nobreakspace N{\cdot }mm A^{-1}$ and efficiency of 28.2 %, which approaches the performance of ...
Joseph Schwalbe +4 more
wiley +1 more source
Nonlocomotory Robotic Strategies for Dynamic Rotation Control in Terrestrial Robots: A Review
Terrestrial robots increasingly require rapid body rotation to maintain stability and agility in complex environments. This review shows nonlocomotory rotational control strategies that operate without ground contact, including reaction wheels, tails, bars, limbs, and thrusters.
Y. Liang +14 more
wiley +1 more source
Gradually bent perylene bisimides (PBIs) isolate structural distortion as the sole variable and exhibit negligible intersystem crossing, uncovering rapid vibrational dephasing as the dominant driver of internal conversion through excited‐state vibrational landscape reorganization.
Wei Zhang +8 more
wiley +2 more sources

