Results 181 to 190 of about 222,342 (217)

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source

From tests to truth: A misclassification-aware machine learning framework for estimating brucellosis seroprevalence in wild canids. [PDF]

PLoS Negl Trop Dis
Sarvestani N, Shams F, Mirshahi A, Pato M, Farbod AJ, Khayatderafshi A, Payami M, Abdous A.   +7 more
europepmc   +1 more source

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source

Breathin' on the edge - the hidden complexity of pilot breathing regulators. [PDF]

Front Physiol
Messo K, Mansikka H.
europepmc   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

A benchmark of semi-supervised scRNA-seq integration methods in real-world scenarios. [PDF]

PLoS Comput Biol
Shen X, He C, Guan L.
europepmc   +1 more source

Diagnostic Accuracy of Multiplex NAAT/PCR and Culture Against Salmonella spp.: A Comparison of Meta-Analytical Methods. [PDF]

Pathogens
Rousou X, Furuya-Kanamori L, Meletis E, Lioupi O, Solomakos N, Kostoulas P, Doi SAR.   +6 more
europepmc   +1 more source

Well-designed k-space coverage is important for good MRI denoising. [PDF]

MAGMA
Wang J, Haldar JP.
europepmc   +1 more source

Overestimation of the Apparent Diffusion Coefficient in Diffusion-Weighted Imaging Due to Residual Fat Signal and Out-of-Phase Conditions. [PDF]

Tomography
Dhanani M, Skwierawska D, Kuder TA, Ohlmeyer S, Uder M, Bickelhaupt S, Laun FB.   +6 more
europepmc   +1 more source

Electrical properties based B 1 + prediction for electrical properties tomography reconstruction evaluation. [PDF]

Magn Reson Med
Meerbothe TG, Jung KJ, Cui C, Kim DH, van den Berg CAT, Mandija S.   +5 more
europepmc   +1 more source