Results 111 to 120 of about 570,318 (292)
Advanced Engineering Materials, EarlyView.Cermets (60 vol.% AISI 316L stainless steel, 40 vol.% recycled MgO), intended for use in aluminum electrolysis, were pre‐oxidized in three furnaces with different heating technologies and subjected to a cryolite corrosion test. The different atmospheres influenced the formation of oxide layers, which in turn affected corrosion resistance and ...
Patricia Kaiser +4 more
wiley +1 more source
Material Performance and Processing Behavior of Polyolefin Waste in Mechanical Recycling
RecyclingThis study investigates the processability and performance limits of high-density polyethylene (HDPE) recovered from mixed polyolefin waste under realistic mechanical recycling conditions. The waste stream was processed by extrusion and injection molding,
Yamila V. Vazquez +4 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.This study investigates the effects of milling parameters, including rotational speed, milling duration, and ball‐to‐powder ratio, on TiAl particle size and morphology in an XHV‐equivalent atmosphere. The creation of oxide‐free surfaces enhances the mechanical properties of green bodies.
Jytte Möckelmann +4 more
wiley +1 more source
Електроніка та інформаційні технологіїBackground. β-Ga2O3 gallium oxideis a promising wide-bandgap semiconductor widely used in optoelectronic and sensing applications. The electrical conductivity of thin films strongly depends on their structural quality, defect states, and post-deposition ...
Ihor Kukharskyy +4 more
doaj +1 more source
Microstructure Evolution of a VMnFeCoNi High‐Entropy Alloy After Synthesis, Swaging, and Annealing
Advanced Engineering Materials, EarlyView.The synthesis and processing (rotary swaging and annealing) of the novel VMnFeCoNi alloy is investigated, alongside the estimation of the grain size effect on hardness. Analysis of a wide grain size range of recrystallized microstructures (12–210 µm) reveals a low annealing twin density.
Aditya Srinivasan Tirunilai +6 more
wiley +1 more source
Linear simulations of a wide pedestal quiescent H-mode plasma with the extended-MHD code NIMROD
Nuclear FusionWe present linear simulations of a Wide Pedestal QH (WPQH)-mode DIII-D plasma with the NIMROD code to address the role of ion multispecies collisionality on WPQH-modes.
J.J. Dominguez-Palacios Duran +5 more
doaj +1 more source
Gas Flow Metering Using National Standards and Gas Mixtures Containing Hydrogen
HydrogenWe present the first European intercomparison of primary flow measurement standards with hydrogen-enriched natural gas (up to 20% hydrogen in molar fraction) and natural gas with pressure up to 60 bar and volume flow rates in the range (5 to 160) m3/h ...
Maxime Mussard +9 more
doaj +1 more source
Production of MgO/TiC Composites From MgO‐C Recyclates Using Spark Plasma Sintering
Advanced Engineering Materials, EarlyView.Using the spark plasma sintering technique, MgO/TiC composites are manufactured from recycled MgO‐C refractories stemming from the steel production that were mixed with titanium powder. This article shows, how the size of the Ti grains and their distribution in the powder mixture affect the local carbon concentration in TiC.
Jiayan Yu +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Viktoriia Shtefan, Thorgund Nemec, Ute Hempel, Annett Gebert and coworkers demonstrate that anodic treatment of Ti–Cu‐based metallic glass in a nontoxic pyrophosphate electrolyte forms a protective bilayered Ti/Zr‐oxide film enriched with Cu nanocrystals.
Viktoriia Shtefan +8 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This plot compares experimental tensile stress–strain curves (with 4 different strain rates) and corresponding modelled curves (obtained using the optimised sets of Voce and Miller–Norton parameter values shown). The inferred M‐N values, characterizing the creep, are very similar to those obtained via conventional creep testing.
S. Ooi, R. P. Thompson, T. W. Clyne
wiley +1 more source