Results 81 to 90 of about 15,451 (231)
MetalMat, Volume 3, Issue 2, June 2026.ABSTRACT Machining of materials is an invaluable technique to give specific shapes and dimensions of desired materials. Different machining processes give rise to different surface characteristics that include not only surface roughness but also specific surface morphology, such as the recast layer.
Animesh Kumar Basak +4 more
wiley +1 more source
Microstructure, Chemical and Phase Composition of Clad Layers of Inconel 625 and Inconel 686
, 2018 The article presents the investigation results of microstructural, chemical composition changes after clad layers of Inconel 625 and Inconel 686 alloys weld overlaid on boiler tubes.
Petrzak, P. +3 more
core +1 more source
Degradation modes and tool wear mechanisms in finish and rough machining of Ti17 Titanium alloy under high-pressure water jet assistance [PDF]
, 2013 This article presents the results of an experimental study on the Ti17 titanium alloy, which was carried out to analyze tool wear and the degradation mechanisms of an uncoated tungsten carbide tool insert. Two machining conditions, roughing and finishing,
GERMAIN, Guénaël +3 more
core +1 more source
LubricantsFriction and high temperatures greatly affect the hardness and processing efficiency of superalloys. Therefore, it is important to provide a coating on their surfaces with a hard layer. In this study, pack boronizing was applied on Inconel 601 to improve
Gonca Uslu +4 more
doaj +1 more source
A Study on Ultrasonic Elliptical Vibration Cutting of Inconel 718
Shock and Vibration, 2016 Inconel 718 is a kind of nickel-based alloys that are widely used in the aerospace and nuclear industry owing to their high temperature mechanical properties. Cutting of Inconel 718 in conventional cutting (CC) is a big challenge in modern industry.
Zhao Haidong +3 more
doaj +1 more source
Archives of Metallurgy and Materials, 2015 Quality requirements and tests taken on the surfacing layer Inconel 625 are presented in the article. The reasons of using surfacing layer Inconel 625 and technologies of its making with a particular emphasis on the CMT method are described.
Słania J., Krawczyk R., Wójcik S.
doaj +1 more source
High Cycle Fatigue Properties of PM‐HIPed High‐Nitrogen Tool Steel: Effect of Surface Condition
Fatigue &Fracture of Engineering Materials &Structures, Volume 49, Issue 6, Page 2097-2115, June 2026.ABSTRACT This study explores the impact of surface condition on high‐cycle fatigue performance of a high‐nitrogen martensitic tool steel manufactured through powder metallurgy and hot isostatic pressing. In near‐net manufacturing applications, acid‐leaching pickling treatment and/or machining is used as a post‐treatment to remove the powder container ...
Faezeh Javadzadeh Kalahroudi +3 more
wiley +1 more source
Journal of the American Ceramic Society, Volume 109, Issue 6, June 2026.ABSTRACT The nature of gel formation on borate glasses during dissolution remains relatively unexplored, despite relevance to bioactive glass applications. In this work, we investigate gel‐layer formation on sodium‐ and potassium‐ modified aluminoborate glasses after dissolution in deionized water.
Jessica J. Sly, John C. Mauro
wiley +1 more source
Residual Stresses in Inconel 625 Parts Produced Using Atomic Diffusion Additive Manufacturing (ADAM) [PDF]
Metal additive manufacturing, also known as metal 3D printing, is a cutting-edge manufacturing process that involves building metal parts layer by layer from a digital 3D model.
Nida Naveed +3 more
core
Tribological properties of cold sprayed INCONEL 625
, 2023 In this study, cold sprayed Inconel 625 coating was applied on to Inconel 625 substrate using high-pressure cold spray system. Dry sliding wear test was performed to investigate the tribological properties of the Inconel 625 coating and substrate at room
Yan, Wei Cheng
core