Results 171 to 180 of about 96,954 (294)

Exploring the Potential of Microwave Annealing for Enhancing Si‐based GeSn Lasers

Advanced Materials Technologies, EarlyView.
We explore low‐thermal‐budget microwave annealing to enhance the performance of group‐IV GeSn lasers on Si. Microwave annealing under optimal conditions can simultaneously relax unwanted compressive strain and enhance the material quality of the GeSn active layer, thereby reducing the threshold and increasing the laser operating temperature.
Yue‐Tong Jheng, Cheng‐Feng Liu, Ruei‐Jhang Wang, Yu Cheng, Lung‐Yi Hsu, Yonder Berencén, Shengqiang Zhou, Hanh Thi‐Thu Tran, Guo‐En Chang   +8 more
wiley   +1 more source

High selective SIW bandpass filter with flexible bandwidth and transmission zero for 5G application. [PDF]

Sci Rep
Mishra GK, Pandey HK, Pathak NP.
europepmc   +1 more source

inductively-coupled plasma robustness

Citation: 'inductively-coupled plasma robustness' in the IUPAC Compendium of Chemical Terminology, 5th ed.; International Union of Pure and Applied Chemistry; 2025. Online version 5.0.0, 2025. 10.1351/goldbook.08492 • License: The IUPAC Gold Book is licensed under Creative Commons Attribution-ShareAlike CC BY-SA 4.0 International for ...
openaire   +1 more source

Degradation Mechanisms in PEM Water Electrolysis: Diagnosis and Impact

Advanced Materials Technologies, EarlyView.
This review provides an analysis of degradation mechanisms in proton electrolyte membrane water electrolyzers (PEMWE), focusing on all key components. It discusses diagnostic and measurement techniques for evaluating degradation, less‐studied mechanisms, and an expert survey.
Annik Bernhardt, Katja Lange, Robert Göckeritz, Erik Grunwald, Angelika Hähnel, Alexander Müller, Volker Naumann, Sistan Rasuli, Wolfram Münchgesang, Bruno G. Pollet, Kerstin Witte‐Bodnar, Klemens Ilse   +11 more
wiley   +1 more source

In Situ Copper Electroplating Turns Material Extrusion 3D Printers Into Metal–Polymer Hybrid Fabricators

Advanced Materials Technologies, EarlyView.
An in situ electroplating approach for MEX 3D printing is proposed, enabling copper deposition during the fabrication of conductive polymers. The method combines a printer‐integrated plating head, ML‐based g‐code control, and stop‐and‐go printing, achieving near‐bulk copper conductivity and enabling fully embedded, assembly‐free electronic components ...
Gianluca Percoco, Nicola Larovere, Antonio Zagaria, Antonio Pavone, Rosanna Rifino, Gianni Stano   +5 more
wiley   +1 more source

An Accessible Microfluidic Platform for the Generation of Polarized Brain Organoids

Advanced Materials Technologies, EarlyView.
This study presents an accessible double‐gradient microfluidic device that enables controlled morphogen delivery and spatially polarized differentiation in brain organoids. By integrating a pump‐free design and stable fabrication method, the platform generates dorsal–ventral neuronal asymmetry, offering a reproducible and versatile approach to model ...
Daniel Pérez‐Calixto, Manuel Alejandro Vazquez Valle, Mitzi Pérez‐Calixto, Cindy Peto‐Gutiérrez, Iván Velasco, Genaro Vázquez‐Victorio, Itzel Escobedo‐Avila   +6 more
wiley   +1 more source

Tunable Extraordinary Optical Transmission in the Long‐Wavelength Infrared Range Using Electrostatic MEMS Actuation

Advanced Materials Technologies, EarlyView.
A MEMS‐integrated metamaterial filter enables continuous, low‐voltage spectral tuning in the long‐wavelength infrared (LWIR). The device employs extraordinary optical transmission in a dual suspended metasurface stack, where electrostatic actuation precisely controls the intermembrane air gap.
Oleg Bannik, Fedor Kovalev, Michal Zawierta, Dilusha Silva, Lorenzo Faraone, Ilya Shadrivov, Mariusz Martyniuk   +6 more
wiley   +1 more source

Additive Manufacturing of Ni‐Based Thermoelectric Materials for Waste Heat Recovery

Advanced Materials Technologies, EarlyView.
Thermoelectric generators convert waste heat into electricity but are constrained by conventional fabrication. Here, laser powder bed fusion enables direct printing of customised n‐type Cu60Ni40 and p‐type Ni90Cr10 legs. The assembled module achieves 0.8% efficiency at ΔT = 419 K, demonstrating scalable additive manufacturing of eco‐friendly, design ...
Karolin Amstein, Aayush Dobhal, Heiko Reith, Ran He, Julia Kristin Hufenbach, Kornelius Nielsch, Pingjun Ying   +6 more
wiley   +1 more source

Magnetic Textiles: A Review of Materials, Fabrication, Properties, and Applications

Advanced Materials Technologies, EarlyView.
Magnetic textiles (M‐textiles) are emerging as a programmable materials platform that merges magnetic matter with hierarchical textile structures. This article consolidates magnetic material classes, textile architectures, and fabrication and magnetization strategies, revealing structure–property–function relationships that govern magneto‐mechanical ...
Li Ke, Moses Kumi, Xiaoming Tao, Junhong Pu   +3 more
wiley   +1 more source

Additive‐Manufactured, Multifunctional Bioreactor Technology for Dynamic Culture of 3D Bioprinted Tissue Models

Advanced Materials Technologies, EarlyView.
We introduce an additively manufactured bioreactor with a perfusion flow system and integrated temperature and pH sensors for skeletal muscle tissue biofabrication. The bioreactor's performance was evaluated by assessing the viability, spreading of the myoblast cells in a printed scaffold, and contraction of the isolated murine musculi interossei ...
Lys Sprenger, Johann Schorzmann, Hsuan‐Heng Lu, Muhammad Osama, Julian Bauer, Michael Haug, Oliver Friedrich, Aldo R. Boccaccini, Frank Döpper, Sahar Salehi   +9 more
wiley   +1 more source