Results 41 to 50 of about 11,197 (265)
Advanced Engineering Materials, EarlyView.This study investigates thermo‐chemical processes during high‐temperature testing of two commercial MgO‐C brick grades, one containing 47.5 wt.% MgO‐C recyclate. Using ETV, DTA/TG‐MS, XRD, and SEM/EDS/EBSD, mechanisms such as carbothermal reduction of magnesia, impurity incorporation into the secondary MgO surface layer, and calcium‐rich phase ...
Alexander Schramm +6 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Carbon‐free inert anodes are essential for decarbonizing aluminum electrolysis. This study investigates a recyclate‐based MgO‐316L steel composite anode tested under galvanostatic Hall–Héroult conditions in cryolite at 1000°C. Microstructural analysis reveals selective MgO fluorination, spinel and oxide layer formation, electrolyte infiltration, and ...
Serhii Yaroshevskyi +7 more
wiley +1 more source
Journal of Vacuum Science & Technology A: Vacuum, Surfaces, and Films, 2005 An inductively coupled plasma (ICP) source enabling high-density plasma generation was developed for large area processing. Technological difficulties related to the scaling up of the coil antenna, dielectric vacuum window, and gas distribution have been addressed.
COLPO Pascal +2 more
openaire +2 more sources
Advanced Engineering Materials, EarlyView.EDX elemental map of the pre‐oxidized MgO–steel cermet anode cross section after electrolysis. The development of inert anodes for aluminum electrolysis remains challenging due to the high corrosivity of cryolite‐based melts at 950°C–1000°C. This study investigates the corrosion and process behavior of a carbon‐free MgO–steel cermet anode derived from ...
Alexander Adamczyk +7 more
wiley +1 more source
Energies, 2021 In this paper a general-purpose procedure for optimizing a resonant inductive wireless power transfer link adopting a multiple-input-multiple-output (MIMO) configuration is presented.
Giuseppina Monti +4 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.The subject of this work is the development of a corrosion‐protective coating on steel sheets for form hardening. Rapid heating in an extreme high vacuum (XHV)‐adequate atmosphere is a useful method to prevent oxidation during alloying of 22MnB5 and aluminum to obtain a metallurgical bonding.
Lorenz Albracht +5 more
wiley +1 more source
An NFC on Two-Coil WPT Link for Implantable Biomedical Sensors under Ultra-Weak Coupling
Sensors, 2017 The inductive link is widely used in implantable biomedical sensor systems to achieve near-field communication (NFC) and wireless power transfer (WPT). However, it is tough to achieve reliable NFC on an inductive WPT link when the coupling coefficient is
Chen Gong +4 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Collagen hydrolysate is evaluated as a sustainable binder for MgO‐C refractories. Its thermally induced cross‐linking and gas release lead to expansion and cracking in large bricks, but tailored batches with lignin, recyclates, or fine graphite improve the gas release while thermal treatment and stability.
Till M. J. Stadtmüller +8 more
wiley +1 more source
Using Some Coupled Numerical Models in Problems of Designing an Inductive Electrothermal Equipment [PDF]
Journal of Electrical and Electronics Engineering, 2014 This paper focuses on the numerical modeling of coupling the electromagnetic and the thermal field, in the process of inductive heating, for inductive electrothermal equipments. Numerical results are carried out by using a FLUX2D application.
LEUCA Teodor +4 more
doaj
Secure Capacity Analysis for Magnetic Inductive Coupling-Based SWIPT System
IEEE Access, 2018 Many researchers have provided meaningful insights for physical layer security (PLS) in various wireless communication systems. However, few works have carried out an intensive PLS analysis for magnetic inductive coupling (MIC)-based simultaneous ...
Sungmin Han +3 more
doaj +1 more source