Results 111 to 120 of about 127,143 (294)

Exploring the Potential of Microwave Annealing for Enhancing Si‐based GeSn Lasers

Advanced Materials Technologies, EarlyView.
We explore low‐thermal‐budget microwave annealing to enhance the performance of group‐IV GeSn lasers on Si. Microwave annealing under optimal conditions can simultaneously relax unwanted compressive strain and enhance the material quality of the GeSn active layer, thereby reducing the threshold and increasing the laser operating temperature.
Yue‐Tong Jheng, Cheng‐Feng Liu, Ruei‐Jhang Wang, Yu Cheng, Lung‐Yi Hsu, Yonder Berencén, Shengqiang Zhou, Hanh Thi‐Thu Tran, Guo‐En Chang   +8 more
wiley   +1 more source

Discovery Learning Experiments in a New Machine Design Laboratory [PDF]

, 2013
A new Machine Design Laboratory at Marquette University has been created to foster student exploration with hardware and real-world systems. The Laboratory incorporates areas for teaching and training, and has been designed to promote “hands-on” and ...
Anton, Fernando Rodriguez, Nagurka, Mark L.   +1 more
core   +1 more source

Benchmarking Coaxial and Angular Optical Emission Spectroscopy With Recommendations for Reliable Compositional In Situ Monitoring During Laser Powder Bed Fusion

Advanced Materials Technologies, EarlyView.
ABSTRACT Real‐time insight into local chemistry is critical for reliable part quality in additive manufacturing, especially laser powder bed fusion (PBF‑LB/M), where rapid thermal cycles and localized evaporation can undermine part performance. Optical emission spectroscopy (OES) offers non‑intrusive, in situ plume monitoring, but detection geometry ...
Philipp Gabriel, Bastian Jülich, Anna Rosa Ziefuss, Florian Eibl, Stephan Barcikowski   +4 more
wiley   +1 more source

Imaging the paramagnetic nonlinear Meissner effect in nodal gap superconductor

, 2017
Boundary surfaces of nodal gap superconductors can host Andreev bound states (ABS) which develop a paramagnetic response under external RF field in contrast to the bulk diamagnetic response of the bulk superconductor.
Anlage, Steven M., Bae, Seokjin, Lukashenko, Alexander V., Omelyanchouk, Alexander N., Shevchenko, Sergey N., Ustinov, Alexey V., Zhuravel, Alexander P.   +6 more
core   +1 more source

Degradation Mechanisms in PEM Water Electrolysis: Diagnosis and Impact

Advanced Materials Technologies, EarlyView.
This review provides an analysis of degradation mechanisms in proton electrolyte membrane water electrolyzers (PEMWE), focusing on all key components. It discusses diagnostic and measurement techniques for evaluating degradation, less‐studied mechanisms, and an expert survey.
Annik Bernhardt, Katja Lange, Robert Göckeritz, Erik Grunwald, Angelika Hähnel, Alexander Müller, Volker Naumann, Sistan Rasuli, Wolfram Münchgesang, Bruno G. Pollet, Kerstin Witte‐Bodnar, Klemens Ilse   +11 more
wiley   +1 more source

Wireless Power Transmission [PDF]

, 2016
Wireless Power Transmission through inductive coupling is one of the new emerging technologies that will bring tremendous change in human life. Due to shortage of time and fast running life style it is difficult to carry the complete charging set which ...
chaurasiya, M. N. (Mr), Gupta, S. K. (Sandeep), Shalu, S. (Shalu), Singh, S. P. (Surya), Yadav, R. (Rishikesh), Yadav, S. P. (Surya)   +5 more
core  

Tunable Extraordinary Optical Transmission in the Long‐Wavelength Infrared Range Using Electrostatic MEMS Actuation

Advanced Materials Technologies, EarlyView.
A MEMS‐integrated metamaterial filter enables continuous, low‐voltage spectral tuning in the long‐wavelength infrared (LWIR). The device employs extraordinary optical transmission in a dual suspended metasurface stack, where electrostatic actuation precisely controls the intermembrane air gap.
Oleg Bannik, Fedor Kovalev, Michal Zawierta, Dilusha Silva, Lorenzo Faraone, Ilya Shadrivov, Mariusz Martyniuk   +6 more
wiley   +1 more source

Communication system for a tooth-mounted RF sensor used for continuous monitoring of nutrient intake [PDF]

, 2019
In this Thesis, the communication system of a wearable device that monitors the user’s diet is studied. Based in a novel RF metamaterial-based mouth sensor, different decisions have to be made concerning the system’s technologies, such as the power ...
Zufía Mier, Pablo
core   +1 more source

Additive Manufacturing of Ni‐Based Thermoelectric Materials for Waste Heat Recovery

Advanced Materials Technologies, EarlyView.
Thermoelectric generators convert waste heat into electricity but are constrained by conventional fabrication. Here, laser powder bed fusion enables direct printing of customised n‐type Cu60Ni40 and p‐type Ni90Cr10 legs. The assembled module achieves 0.8% efficiency at ΔT = 419 K, demonstrating scalable additive manufacturing of eco‐friendly, design ...
Karolin Amstein, Aayush Dobhal, Heiko Reith, Ran He, Julia Kristin Hufenbach, Kornelius Nielsch, Pingjun Ying   +6 more
wiley   +1 more source

Investigation of current balance methodologies for inductive power transfer coupler with multiple branches

IET Power Electronics
In the inductive power transfer (IPT) system, using multiple coil branches instead of a whole large coil can effectively solve the thickness problem and save space.
Mengna Luo, Zhicong Huang
doaj   +1 more source