Results 1 to 10 of about 13,274 (262)

Household Induction Cookers: Calculation and Design of Structural Elements

open access: yesVìsnik Nacìonalʹnogo Tehnìčnogo Unìversitetu Ukraïni Kììvsʹkij Polìtehnìčnij Ìnstitut: Serìâ Radìotehnìka, Radìoaparatobuduvannâ, 2021
A technique for calculation and design of main structural elements of household induction cookers – inductors and magnetic cores is proposed. The technique consists of two stages.
M. G. Pantelyat   +3 more
doaj   +1 more source

Evaluating the Effectiveness of Magnetic-Pulse Treatment for Healing Continuity Defects in the Metal of Oil and Gas Pipelines

open access: yesMetals, 2023
This research paper addresses the issues in evaluating the effectiveness of magnetic-pulse treatment for healing continuity defects in the metal of oil and gas pipelines. A theoretical analysis of the magnetic-pulse action mechanism on continuity defects
Andrey Schipachev   +5 more
doaj   +1 more source

Integrated Square On-Chip Inductor for Photovoltaic Converter Applications

open access: yesRevue des Énergies Renouvelables
The research of this paper concerns the study of an integrated square on-chip inductor in a DC-DC Buck converter connected to a photovoltaic module.
mokhtaria derkaoui, Yamina Benhadda
doaj   +1 more source

INDUCTION HEATING IN HISTORY AND DEVELOPMENT. APPLICATION IN MODERN TRANSPORT REPAIRING TECHNOLOGIES [PDF]

open access: yesAvtomobilʹnyj Transport (Harʹkov), 2017
The technologies used in repair of vehicles were analyzed in the given paper. The shortcomings of the mechanical repair methods in question can be solved by using induction heating.
Yu. Batyhin, O. Sabokar, V. Strelnikova
doaj  

Optimizing the Process of Inductive Heating in Volume Using Numerical Simulations [PDF]

open access: yesJournal of Electrical and Electronics Engineering, 2017
This paper presents a modeling process, using the 2D Flux software and an optimization process, based on the Response Surface Method, Central Composite Design, from the Minitab Statistical Software.
CODREAN Marius   +3 more
doaj  

Modeling of the process of heating of chip‑powder dispersions of ferrous metals in the pass‑through muffle furnace of hot briquetting. Message 2

open access: yesЛитьë и металлургия, 2022
The simulation of the chip heating process in the zones of gas-flame and induction heating of a continuous muffle furnace has been carried out. The mechanisms of heat transfer (conductive, convective, radiative) that have a conjugated character are ...
O. M. Dyakonov   +2 more
doaj   +1 more source

Bubble inductors: Pneumatic tuning of a stretchable inductor [PDF]

open access: yesAIP Advances, 2017
From adaptive matching networks in power systems to channel selectable RF filters and circuitry, tunable inductors are fundamental components for circuits requiring reconfigurability. Here we demonstrate a new continuously tunable inductor based on physically stretching the inductor traces themselves.
Nathan Lazarus, Sarah S. Bedair
openaire   +2 more sources

Equivalent circuit of an inductor on a nanocrystalline core with a high magnetic permeability

open access: yesФизика волновых процессов и радиотехнические системы, 2022
Based on the measured impedance of the inductors based on a toroidal core wound from a thin (18 m) nanocrystalline tape, with a different number of winding turns, an equivalent high frequency (0 Hz - 500 MHz) circuit model was built.
Vladimir F. Dmitrikov   +2 more
doaj   +1 more source

Numerical-Field Calculation of the Angle Torque Characteristic of the Three-Phase Inductor of the Magnetic Field of the Electromagnetic Stirrer in Processing Dissimilar Mixtures [PDF]

open access: yesProblems of the Regional Energetics, 2019
The evaluation of the possibility of using electromagnetic stirrers for dissimilar mixtures in various technological processes requires the study of their work under load conditions.
Milykh V.I., Shilkova L.V.
doaj   +1 more source

Utilization of Euler-Lagrange Equations in Circuits with Memory Elements [PDF]

open access: yesRadioengineering, 2016
It is well known that the equation of motion of a system can be set up using the Lagrangian and the dissipation function, which describe the conservative and dissipative parts of the system.
Z. Biolek, D. Biolek, V. Biolkova
doaj  

Home - About - Disclaimer - Privacy