Results 81 to 90 of about 682 (265)

Stresses evolution at high temperature (200°C) on the interface of thin films in magnetic components

EPJ Web of Conferences, 2014
In the field of electronics, the increase of operating temperatures is a major industrial and scientific challenge because it allows reducing mass and volume of components especially in the aeronautic domain.
Doumit Nicole, Danoumbé Bonaventure, Capraro Stéphane, Chatelon Jean-Pierre, Nader Chadi, Habchi Roland, Piot Alain, Rousseau Jean-Jacques   +7 more
doaj   +1 more source

Is an Apple an Orange? A Large Language Model Benchmark for Candidate Term Extraction and Subclass Decisions Against Upper Ontologies in Engineering and Materials Science

Advanced Engineering Materials, EarlyView.
Building machine‐readable vocabularies for materials science is slow, expert‐driven work. This study benchmarks 13 large language models on two of its first steps: finding candidate terms in engineering articles and deciding where they belong in a class hierarchy.
Thomas Bjarsch, Maximilian Holland, Klaus Drechsler, Johannes Schilp   +3 more
wiley   +1 more source

A Low-Cost Analog Circuit Implementation of the Jiles-Atherton Hysteresis Model

IEEE Access
We show the design of a broadband, fully analog circuit for simulating the hysteretic $B-H$ characteristics of magnetic core materials closely following the Jiles-Atherton model using standard electronic components.
Thomas Voglhuber-Brunnmaier, Bernhard Jakoby   +1 more
doaj   +1 more source

Hydrogen‐Assisted Fracture of Iron‐Based Fe–Ni–Al Alloys

Advanced Engineering Materials, EarlyView.
Principal relations and fracture mechanisms of single‐phase and precipitate‐strengthened Fe–Ni–Al alloys subjected to prior electrochemical hydrogen charging are identified. The mechanisms of hydrogen effect on strength and microhardness are discussed, including hydrogen‐induced increase in microhardness and the role of hydrogen in fracture behavior ...
Nataliya Yadzhak, Olha Zvirko, Rostyslav Leshchak, Hryhoriy Nykyforchyn   +3 more
wiley   +1 more source

Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A

Advanced Engineering Materials, EarlyView.
The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han, Julian M. Rosalie, Jan Radners, Mauro Madia, Philipp von Hartrott, Birgit Skrotzki   +5 more
wiley   +1 more source

Recycling of NiTi Shape Memory Alloys: Fundamental and Technological Aspects of a Vacuum Induction Melting Processing Route

Advanced Engineering Materials, EarlyView.
The present study investigates recycling of NiTi shape memory alloys via vacuum induction melting. An ingot was synthesized from elemental Ni and Ti and subjected to three subsequent remelting cycles. Remelting increases process durations and impurity levels and adversely affects microstructures and functional properties.
Sakia Sophia Noorzayee, Son Tung Mai, Sarath Menon, Braulio Gadiel Sánchez Ortega, Ralf Drautz, Alexander Kauffmann, Gunther Eggeler, Jan Frenzel   +7 more
wiley   +1 more source

Precipitation Simulations of the O‐Phase in Ti2AlNb Alloys Processed by Laser Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
Simulated and experimental evolution of the O‐phase volume fraction during postprocessing of a Ti‐21Al‐25Nb (at.%) alloy processed by laser powder bed fusion. With results of sensitivity to input parameters from a thorough and quantified analysis, the interfacial energy matrix/precipitate is the most relevant input parameter for the simulation of the O‐
Silvana Tumminello, Joachim Gussone, Suzana G. Fries, Marcus Rackel, Andreas Stark, Norbert Schell, Jan Haubrich, Guillermo Requena   +7 more
wiley   +1 more source

Low-Loss Soft Magnetic Materials and Their Application in Power Conversion: Progress and Perspective

Energies
Amorphous and nanocrystalline alloys, as novel soft magnetic materials, can enable high efficiency in a wide range of power conversion techniques. Their wide application requires a thorough understanding of the fundamental material mechanisms, typical ...
Weiwang Wang, Jiaqi Fan, Changshen Li, Yue Yu, Anding Wang, Shengtao Li, Jinjun Liu   +6 more
doaj   +1 more source

Swelling‐Programmed Topographical Guidance for Dynamic Spheroid Self‐Assembly via a Mechanochemical Hydrogel Niche

Advanced Functional Materials, EarlyView.
A swelling‐programmed micropatterned hydrogel guides adherent cells through a controlled transition from cell–matrix anchoring to cadherin‐mediated cell–cell compaction, enabling rapid assembly of high‐viability spheroids with defined size and morphology.
Han Gyeol Nam, Seon Yeong Chae, Young Woo Kwon, Hye Jin Heo, Hye Rin Lee, Ji Hyeok Lee, Dong‐Wook Han, Yun Hak Kim, Suck Won Hong   +8 more
wiley   +1 more source

Solution‐Processed Two‐Dimensional Indium Oxide on Sodium‐Embedded Alumina for Reconfigurable Optoelectronic Synaptic Transistors

Advanced Functional Materials, EarlyView.
Wafer‐scale two‐dimensioanl In2Se3 oxidized into InOx on sodium‐embedded beta‐alumina enables multifunctional reconfigurable electronics. Sodium ions accumulate within distinct spatial distribution under drain‐controlle and gate‐controlled operation. Drain‐control operation gives controllability of ultraviolet‐driven optoelectronic synaptic conductance
Jinhong Min, Yonghyun Albert Kwon, Hyunbin Kim, Jihyun Kim, Myeongjin Jung, Jaewon Heo, Gwang Ya Kim, Vlastimil Mazanek, Zdeněk Sofer, In Soo Kim, Jeong Ho Cho, Hyesung Park, Sang Min Won, Joohoon Kang   +13 more
wiley   +1 more source