Results 111 to 120 of about 5,549,865 (294)

Municipal industrial building bond plans [1953]

, 1953
December 1953Foreword -- Introduction and Summary -- Comparative Features -- Facilities Authorized -- Units Authorized to Use the Plans -- Area Within Which Plants May be Built -- Table I - Municipal Industrial Building Bonds Acts -- Type of Bonds ...
Kansas Industrial Development Commission, Research Division
core  

Distinct Microstructural Characteristic Lengths Defining Notch Fatigue Crack Initiation and Propagation, and Defect Tolerance in Advanced Steels

Advanced Engineering Materials, EarlyView.
Schematic representation of modes of microcrack nucleation, growth and temporary arrestment at different boundaries, with the criteria for crack propagation in three scenarios: (1) large notch, (2) defect/small sharp notch, and (3) long crack. This work revisits and integrates results on the fatigue behavior of advanced bainitic steels (in particular ...
Lucia Morales‐Rivas
wiley   +1 more source

Microstructure Modification of Additively Manufactured Mo–9Si–8B by Annealing and Its Effects on High‐Temperature Mechanical Properties

Advanced Engineering Materials, EarlyView.
Postbuild annealing systematically modifies the phase fractions and morphology of EB‐PBF processed Mo–9Si–8B. Quantitative microstructure–property correlations reveal how controlled phase evolution enhances high‐temperature compressive strength and creep resistance.
Christopher Schmidt, Yong Chen, Georg Hasemann, Benjamin Wahlmann, Carolin Körner, Manja Krüger   +5 more
wiley   +1 more source

Application of Carbon Nanofiber-Modified Concrete in Industrial Building Design.

Int J Anal Chem, 2023
Liu T.
europepmc   +1 more source

Uniform Amorphization of Crystalline Silicon Surfaces Enabled by Deep Ultraviolet Femtosecond Laser Pulses

Advanced Engineering Materials, EarlyView.
Deep‐UV (258 nm) femtosecond pulses enable uniform amorphous silicon writing on Si(100)/(111) with a six‐fold larger fluence amorphization window than NIR methods. Optimized fluence and overlap yield 20–45 nm uniform and continuous amorphous layers. Microscopy shows sharp interfaces, and real‐time reflectivity reveals nanosecond melt–resolidification ...
Wissal Benali, Magali Gregoire, Matys Guyard, Tatiana Itina, David Grojo, Pol Sopeña   +5 more
wiley   +1 more source

Superlubricity and Corrosion Inhibition Properties of Solvate Ionic Liquids in Hybrid Carbon Fiber Reinforced Plastic–Steel Interfaces

Advanced Engineering Materials, EarlyView.
Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees, Timothy Harte, Bhagya Dharmasiri, Y. Athulya Wickramasingha, David J. Hayne, Daniel J. Eyckens, Luke C. Henderson   +6 more
wiley   +1 more source

Capacity building towards sustainability: Context of post disaster waste management [PDF]

Concept of Capacity Building is an essential component in development theory and practice. In developing countries, it is identified as a key concept in achieving sustainability. In particular, in post disaster scenarios, focus has been placed upon local
Amaratunga, Dilanthi, Haigh, Richard, Karunasena, G. I.   +2 more
core   +3 more sources

Architecture‐Driven Sensor Stability in Weft‐Knitted Engineering Textiles

Advanced Engineering Materials, EarlyView.
Textile‐integrated sensor architectures are systematically compared to evaluate their electromechanical behavior under combined mechanical and environmental loading. Pocket‐based integration exhibits stable and reproducible signals, whereas tunnel‐based routing shows higher sensitivity accompanied by increased variability.
Adnan Maroof Khan, Johannes Wendler, Dilbar Aibibu, Johannes Mersch, Michael Wöltje, Chokri Cherif   +5 more
wiley   +1 more source

Evaluating the effects of comprehensive simulation on central venous catheterization training: a comparative observational study

BMC Medical Education
Background Simulation-based training (SBT) is vital to complex medical procedures such as ultrasound guided central venous catheterization (US-IJCVC), where the experience level of the physician impacts the likelihood of incurring complications.
Haroula M. Tzamaras, Dailen Brown, Jessica Gonzalez-Vargas, Jason Moore, Scarlett R. Miller   +4 more
doaj   +1 more source

Adaptive Foam 3D Printing of Ultralight and Multifunctional Materials

Advanced Engineering Materials, EarlyView.
Adaptive foam 3D printing, enabled by expandable microspheres, imparts cellular structures to thermoplastic and thermosetting polymers, manufactured through a variety of processes including fused filament fabrication, direct ink writing, digital light processing, and inkjet printing.
Nariman Rajabifar, Amir Ameli
wiley   +1 more source