Results 31 to 40 of about 130,101 (263)

Green Finance Instruments as a Factor of Increasing Industrial Waste Utilization in Russia

Финансы: теория и практика, 2022
Influenced by the governmental policy of national economy decarbonization and greening fundamentally new institution of green finance is currently developing in Russia.
N. A. Osokin, Yu. V. Nikitushkina, I. Yu. Zolotova   +2 more
doaj   +1 more source

Carboxylic‐Acid Functionalized Multiwalled Carbon Nanotube‐Alkane‐Based Resistive Temperature Sensor for Cold Chain Applications

Advanced Engineering Materials, EarlyView.
This study presents a reversible temperature sensor with high switching ratio, ∼103. The device is fabricated using PET‐ITO and carbon nanotube dispersions in alkane. Considering its application in cold chain logistics, a proof‐of‐concept with LED is showcased. Thus, a temperature drop below the threshold temperature (crystallization temperature of the
Sunil Kumar Behera, Philippe Marrec, A. Jorge Parola, Madalena Dionísio, Hugo Águas, Andreia F. M. Santos, Hamed Pourkheirollah, Donald Lupo, César A. T. Laia   +8 more
wiley   +1 more source

Electronic Waste Disassembly with Industrial Waste Heat [PDF]

Environmental Science & Technology, 2013
Waste printed circuit boards (WPCBs) are resource-rich but hazardous, demanding innovative strategies for post-consumer collection, recycling, and mining for economically precious constituents. A novel technology for disassembling electronic components from WPCBs is proposed, using hot air to melt solders and to separate the components and base boards.
Chen, Mengjun, Wang, Jianbo, Chen, Haiyian, Ogunseitan, Oladele A, Zhang, Mingxin, Zang, Hongbin, Hu, Jiukun   +6 more
openaire   +4 more sources

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source

Zein‐Based Adhesives: Sustainable Extraction and Application in Bioadhesive Technologies

Advanced Engineering Materials, EarlyView.
Zein is extracted from corn gluten meal using a simple and scalable process with high yield (~90%). The resulting protein is applied in bioadhesives modified with Ca2+ and Fe3+ ions, exhibiting substrate‐dependent adhesion. The findings demonstrate competitive bonding performance and highlight the role of ionic interactions in tuning adhesion ...
Paula Bertolino Sanvezzo, Daniela Winsley Valereto Friozi, Vinícius de Oliveira, Marcia Cristina Branciforti   +3 more
wiley   +1 more source

Formaldehyde Oxidation of Ce_0.8Zr_0.2O₂ Nanocatalysts for Room Temperature: Kinetics and Effect of pH Value

Nanomaterials, 2023
Ce0.8Zr0.2O2 catalysts were prepared via the co-precipitation method under different pH conditions. The catalysts were characterized via TEM, XRD, XPS, BET, Raman, and FTIR. The oxidation performance of formaldehyde was tested.
Zonglin Yang, Gaoyuan Qin, Ruijiu Tang, Lijuan Jia, Fang Wang, Tiancheng Liu   +5 more
doaj   +1 more source

Productivity‐Driven Optimization of Laser Powder Bed Fusion Parameters for IN718 Superalloy: Process Control, Microstructure, and Mechanical Properties

Advanced Engineering Materials, EarlyView.
This study demonstrates how optimizing laser power, scanning speed, and hatching distance in laser powder bed fusion can boost the productivity of Inconel 718 manufacturing by up to 29% while maintaining mechanical integrity. The work delivers a validated process window and cost–time analysis, offering industry‐ready guidelines for efficient additive ...
Amir Behjat, Guido Barale, John Stavridis, Ehsan Norouzi, Jin‐Yoo Suh, Dong‐Ik Kim, Luca Iuliano, Abdollah Saboori   +7 more
wiley   +1 more source

From Waste to Product: New Circularity by Recovering Polypropylene from Mixed Commercial Waste

Recycling
To meet the EU’s ambitious recycling targets, it is crucial to expand mechanical recycling to include currently underutilized waste streams, such as mixed commercial waste (MCW), which today achieves a recycling rate of only 3–5%.
Maximilian Julius Enengel, Julia Roitner, Lisa Kandlbauer, Tatjana Lasch, Markus Lehner, Renato Sarc   +5 more
doaj   +1 more source

Tanah untuk sanitasi lingkungan terhadap limbah cair industri

Majalah Kulit, Karet, dan Plastik, 1996
Industrial waste management, especially industrial waste water usually is carried out using a high mechanical system, which is need a relative expensive cost. This is not adjustable for small and medium scale industry.
Susilowati Susilowati
doaj   +1 more source

Additive Manufacturing of Continuous Fibre Reinforced Composites: Process, Characterisation, Modelling, and Sustainability

Advanced Engineering Materials, EarlyView.
Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley   +1 more source