Results 51 to 60 of about 36,582 (217)

Lattice Structures for Bone Replacement: The Intersection of Bone Biomechanics, Lattice Design, and Additive Manufacturing

Advanced Materials Technologies, EarlyView.
This review outlines how understanding bone's biology, hierarchical architecture, and mechanical anisotropy informs the design of lattice structures that replicate bone morphology and mechanical behavior. Additive manufacturing enables the fabrication of orthopedic implants that incorporate such structures using a range of engineering materials ...
Stylianos Kechagias, Maxwell J. Munford, Frederik C.H. Masure, Richard J. van Arkel, Reece N Oosterbeek   +4 more
wiley   +1 more source

Microstructure Evolution of Inertia Friction Welded Joints of TC21 Titanium Alloy

Processes, 2022
In this paper, TC21 titanium alloy welded joints were successfully formed through inertial friction welding (IFW) processes. Microstructure evolution of IFW joints was investigated by way of different analysis methods including optical microscope (OM), scanning electron microscope(SEM), Electron Back-Scattered Diffraction(EBSD), X-Ray Diffraction(XRD),
Hongying Wang, Zihao Li, Shengsheng Zhao, Zhijun Li, Weijie Tang, Fayu Wu, Jun Zhou   +6 more
openaire   +1 more source

Effect of Variations in the Ring Thickness on the Dynamic Performance of the Bimetal Gears

International Journal of Mechanical System Dynamics, EarlyView.
ABSTRACT This study used a six‐degrees‐of‐freedom dynamic model to analyze the dynamic response of bimetal spur gears. Aluminum alloy forms the core of the bimetal gears, and a uniform‐thickness steel ring surrounds the teeth. Gear mesh stiffness of bimetal gears and the transmission error have been assessed using a numerical approach based on finite ...
Bikramjit Singh, Pawan Kumar, S. P. Harsha   +2 more
wiley   +1 more source

Characterization of Fuel Rods Supported by Dimple‐Less Spacer Grids and Subjected to Nonlinear Vibrations

International Journal of Mechanical System Dynamics, EarlyView.
ABSTRACT An experimental campaign was undertaken to demonstrate the applicability of the Bouc–Wen hysteretic model to describe the hysteretic system of the recent Framatome dimple‐less spacer grid design for Pressurized Water Reactors. The experimental setup subjected a reduced‐length fuel rod, supported at both ends by dimple‐less grids, to forced ...
Giovanni Ferrari, Brian Painter, Kostas Karazis, Marco Amabili   +3 more
wiley   +1 more source

Strain Development During Cure of Partially Pre‐Cured Thermosetting Composites Measured With Distributed Fiber Optic Sensors

Polymer Composites, EarlyView.
Schematic representation of the beneficial effect of ply pre‐curing on temperature overshoot, internal strain and warpage during cure of thin and thick thermosetting composites. ABSTRACT Detection of manufacturing‐induced defects in thermosetting composites is crucial to guarantee part quality, safety, and improve manufacturing efficiency.
Francesco Taddei, Giacomo Struzziero, Valentin Ott, Véronique Michaud   +3 more
wiley   +1 more source

Compression capacity of closely spaced double‐angle beam‐columns – Impact of joint stiffness

Steel Construction, EarlyView.
Abstract Usually, pinned ends are assumed to calculate the compression capacity of closely spaced double‐angle members. In reality, the joints used in practice provide additional rotational restraint at the member's ends, which significantly influence the compression member capacity of such built‐up sections.
Paul Zauchner, Markus Kettler, Harald Unterweger   +2 more
wiley   +1 more source

Application of Optimal Control Algorithm to Inertia Friction Welding Process

IEEE Transactions on Control Systems Technology, 2013
Inertia friction welding (IFW) is a rotational pressure welding process and is a technique commonly used in the production of aircraft engine shafts. With the ever-increasing achievable production tolerances in terms of the upset and angular orientation, it follows that a significant improvement in the control of these quality parameters is called for.
Loehe, J, Lotz, M, Cannon, M, Kouvaritakis, B   +3 more
openaire   +1 more source

From plant to fabric: Environmental opportunities associated with annatto dye for sustainable development in the textile industry

Coloration Technology, EarlyView.
Abstract Natural dyes are compounds that occur naturally in several organisms and are classified based on chemical structure and application method. The literature cites several natural dyes used in industrial transformation processes. Annatto dye is used in the food industry, and its biological pigment is extracted from the annatto seed. However, this
Marcel Jefferson Gonçalves, Tania Maria Costa, Karine Thaise Rainert, Vera Lúcia Vogel Faustino dos Santos, Ivonete Oliveira Barcellos, Lorena Benathar Ballod Tavares   +5 more
wiley   +1 more source

Strategies for achieving real‐world robustness in topologically engineered surfaces with special wettability

Droplet, Volume 5, Issue 1, January 2026.
Engineered topologies surfaces with special wettability are promising for their ability to precisely customize wetting behaviors and incorporate versatile functionalities, setting them apart from randomly structured surfaces. However, robustness and durability have been hurdles to their broad application.
Sin‐Yung Siu, Yeonhui Choo, Chiu‐Wing Chan, Xiaonan Liu, Chuanbo Hu, Zuankai Wang, Kangning Ren   +6 more
wiley   +1 more source

Misrecognition and Responsibilisation in Extreme Events: Towards Recognition‐based Accountability in Academia

British Journal of Management, Volume 37, Issue 1, January 2026.
Abstract This essay interrogates how extreme events including the COVID‐19 pandemic, climate disasters, and political conflict, amplify structural inequalities in academia. Drawing on critical autoethnographic material from an Early Career Researcher with intersecting marginalisations, we show how crises expose and intensify two mutually reinforcing ...
Milena Tekeste, Mustafa F. Özbilgin
wiley   +1 more source