Results 41 to 50 of about 75,976 (238)

Experimental assessment and retrofit of full-scale models of existing RC frames [PDF]

, 2002
PSD tests on two full-scale models of existing non-seismic resisting RC frame structures are described. The testing program covered several aspects, namely assessment of seismic performance of existing frames without and with infill panels ...
Molina, J., Pinto, A. V., Varum, H.
core   +1 more source

From 3D Models to 3D Prints: an Overview of the Processing Pipeline [PDF]

, 2017
Due to the wide diffusion of 3D printing technologies, geometric algorithms for Additive Manufacturing are being invented at an impressive speed. Each single step, in particular along the Process Planning pipeline, can now count on dozens of methods that
Attene, Marco, Ellero, Stefano, Lefebvre, Sylvain, Livesu, Marco, Martìnez, Jonás   +4 more
core   +5 more sources

Bistable Mechanisms 3D Printing for Mechanically Programmable Vibration Control

Advanced Engineering Materials, EarlyView.
This work introduces a 3D‐printed bistable mechanism integrated into tuned mass dampers (TMDs) for mechanically adaptive passive vibration suppression. Through optimized geometry, the bistable design provides adaptable vibration reduction across a broad range of scenarios, achieving effective vibration mitigation without complex controls or external ...
Ali Zolfagharian, Frédéric Demoly, Mohammad Lakhi, Bernard Rolfe, Mahdi Bodaghi   +4 more
wiley   +1 more source

Numerical model to account for the influence of infill masonry on the RC structures behaviour [PDF]

, 2005
It is a common misconception considers that masonry infill walls in structural RC buildings can only increase the overall lateral load capacity, and, therefore, must always be considered beneficial to seismic performance.
Costa, A., Rodrigues, H., Varum, H.
core   +1 more source

Enhancing Corrosion Resistance and Mechanical Strength of 3D‐Printed Iron Polylactic Acid for Marine Applications via Laser Surface Texturing

Advanced Engineering Materials, EarlyView.
Laser surface texturing significantly improves the corrosion resistance and mechanical strength of 3D‐printed iron polylactic acid (Ir‐PLA) for marine applications. Optimal laser parameters reduce corrosion by 80% and enhance tensile strength by 25% and ductility by 15%.
Mohammad Rezayat, Mojtaba Karamimoghadam, Mohammadreza Lalegani Dezaki, Ali Zolfagharian, Giuseppe Casalino, Antonio Mateo, Mahdi Bodaghi   +6 more
wiley   +1 more source

$X_{max}^{\mu}$ vs. $N^{\mu}$ from Extensive Air Showers as estimator for the mass of primary UHECR's. Application for the Pierre Auger Observatory

, 2014
We study the possibility of primary mass estimation for Ultra High Energy Cosmic Rays (UHECR's) using the $X_{max}^{\mu}$ (the height where the number of muons produced on the core of Extensive Air Showers (EAS) is maximum) and the number $N^{\mu}$ of ...
Arsene, Nicusor, Sima, Octavian
core   +1 more source

Time‐Dependent Oxidation and Scale Evolution of a Wrought Co/Ni‐Based Superalloy

Advanced Engineering Materials, EarlyView.
This study shows how a new wrought Co/Ni‐based superalloy resists oxidation at 800 ∘$^\circ$C. The oxide scale changes from rough, fast‐growing spinel to a dense, protective chromia–alumina layer. Atom probe analysis reveals tiny refractory‐rich bubbles at the interface that mark the transition to long‐term, diffusion‐controlled protection ...
Cameron Crabb, Zachary T. Kloenne, Samuel R. Rogers, Chi Hang Dominik Kwok, Mark C. Hardy, Michele S. Conroy, David Dye   +6 more
wiley   +1 more source

Damage-imperfection indicators for the assessment of multi-leaf masonry walls under different conditions [PDF]

, 2018
The complexity of multi-leaf masonry walls suggests further researches on the dy- namic behaviour mainly characterized by incoherent response between the different layers.
Aldreghetti, Ivano, Baraldi, Daniele, Boscato, Giosuè, Cecchi, Antonella, Massaria, Lorenzo, Reccia, E., Tofani, Italo   +6 more
core  

3D (Bio) Printing Combined Fiber Fabrication Methods for Tissue Engineering Applications: Possibilities and Limitations

Advanced Functional Materials, EarlyView.
Biofabrication aims at providing innovative technologies and tools for the fabrication of tissue‐like constructs for tissue engineering and regenerative medicine applications. By integrating multiple biofabrication technologies, such as 3D (bio) printing with fiber fabrication methods, it would be more realistic to reconstruct native tissue's ...
Waseem Kitana, Indra Apsite, Leonid Ionov   +2 more
wiley   +1 more source

Robust and Reversible Thermofluorescence in Solvent‐Free Thermoplastic Polyurethane Composites

Advanced Functional Materials, EarlyView.
Thermofluorescent polymer composites with high‐contrast optical outputs are prepared by solvent‐free blending of indenoquinacridone dye into a thermoplastic polyurethane matrix. The temperature‐dependent fluorescence originates from aggregation–dissociation of the dye molecules, regulated by competing hydrogen bonds from the polymer matrix.
Guanghua Yu, Bowen Tian, Jazmine Aiya Marquez, Chia‐Min Hsieh, Qingsheng Wang, Hung‐Jue Sue, Mohammed Al‐Hashimi, Peiran Wei, Lei Fang   +8 more
wiley   +1 more source