Results 201 to 210 of about 38,649 (299)

Enhancing tensile strength of 3D-printed wood-PLA composites via a particle swarm optimization framework. [PDF]

PLoS One
Bhattacharjee B, Mathiyalagan P, Prasad KV, Thatoi DN, Singh V, Kumar GS, K R, Panda JK.   +7 more
europepmc   +1 more source

3D‐Printed Crosslinked Nanocellulose‐MXene Hydrogels and Aerogels with High Strength and Conductivity

Small, EarlyView.
This study presents a robust strategy for 3D printing conductive, mechanically resilient MXene–CNF composite structures using a single‐step freeze‐induced crosslinking method. The printed architectures remain stable in both wet and dry states, exhibit high electrical conductivity and mechanical strength, and demonstrate practical application in fully ...
Nuzhet Inci Kilic, Kyle Matthews, Giovanni Marco Saladino, Yury Gogotsi, Per A. Larsson, Mahiar Max Hamedi   +5 more
wiley   +1 more source

A Taguchi-Based and Data-Driven Assessment of Surface Roughness and Wettability in FDM-Printed Polymers. [PDF]

Micromachines (Basel)
Albaşkara M, Gerçekcioğlu E.
europepmc   +1 more source

Incremental upper bound modeling of concrete failures in timber‐concrete notched connections

Structural Concrete, EarlyView.
Abstract This paper introduces a novel theoretical framework for developing incremental upper bound solutions, which is applied to predict the response of two local concrete failures in timber‐concrete composite (TCC) decks with notched connections. The new approach enables a prediction of the capacity at the onset of failure as well as the entire post‐
Peter K. Rasmussen, Linh C. Hoang, Jesper H. Sørensen, Bent Feddersen   +3 more
wiley   +1 more source

Investigation on Mechanical Properties of Functional Graded Hybrid TPMS Structures Inspired Bone Scaffolds. [PDF]

Polymers (Basel)
Karamanli İA.
europepmc   +1 more source

Innovative development and structural behavior of hollow columns using inflatable molds

Structural Concrete, EarlyView.
Abstract This study introduces a novel approach for constructing hollow columns using precast (PC) methods enhanced by inflatable air tubes as internal molds. The proposed method addresses practical challenges in conventional hollow column construction, such as limited constructability, high production cost, and interference between internal molds and ...
Soo Hyung Kim, Dohak Kim, Jeongun Lee, Yun Mook Lim   +3 more
wiley   +1 more source

Radiation Attenuation Calculation of 3D-Printed Polymers Across Variable Infill Densities and Phase Angles for Nuclear Medicine Applications. [PDF]

Polymers (Basel)
Lopez TB, Cabalhug JH, Arriola E, Afable ML, Lorenzo RJW, Fronda GB, Mecarandayo P, Santos GN, Advincula R, Astronomo A, Alvarez MJ.   +10 more
europepmc   +1 more source

Flexural performance of concrete‐filled steel tubular beams with wood chip aggregate

Structural Concrete, EarlyView.
Abstract This study investigates the flexural performance of concrete‐filled steel tubular (CFST) beams with partial replacement of aggregates by wood chips (0%–25%) through experimental and numerical analysis. This study is novel in that it experimentally and numerically investigates the flexural behavior of CFST beams with partial replacement of ...
Mizan Ahmed, Mohamed Emara, Vipulkumar Ishvarbhai Patel, Wensu Chen, Xihong Zhang, Faiz Shaikh, Ahmed Hamoda   +6 more
wiley   +1 more source

Mechanical Parameters and Microstructural Evolution of FDM-Printed PLA and PLA+CF Under Variable Infill Architecture and Lubricant Exposure. [PDF]

Polymers (Basel)
Hozdić E, Hozdić E.
europepmc   +1 more source