Results 101 to 110 of about 129,889 (268)

High Performance Zn–Mn Cement Batteries for the Next Generation of Buildings

Nano-Micro Letters
Highlights Conventional cementitious materials were engineered into active cementitious separators (ACSs) that function as capacity boosters rather than passive carriers, significantly enhancing the capacity of Zn–Mn batteries. Continously generated zinc
Zhaolong Liu, Pan Feng, Long Yuan, Ruidan Liu, Xiangyu Meng, Guanghui Tao, Jian Chen, Zaiping Guo, Changwen Miao   +8 more
doaj   +1 more source

Experimental Characterization and Constitutive Modeling of the Effect of Prior Inelastic Strain on the Viscoplastic Behavior of AD730 at 700 °C

Advanced Engineering Materials, EarlyView.
This study shows that superalloys used in aircraft engine disks become much more prone to deformation at high temperatures if they have been strained during manufacturing. This effect increases with the level of prior strain but eventually reaches a limit.
Fabio Machado Alves da Fonseca, Patrick Villechaise, Malik Durand, Arnaud Longuet, Florent Coudon, Loïc Signor, Julien De Jaeger, Dominique Eyidi, Nathalie Bozzolo, Jonathan Cormier   +9 more
wiley   +1 more source

Natural radon levels act as markers of hydrodynamic behavior in the mountain karst aquifer of Bossea Cave, Italy

Scientific Reports
Radon originating from meta-volcanics located at the bottom of Bossea karstic mountain aquifer is subject to transport within the cave through both advective and diffusive processes.
Luca Biamino, Chiara Colombero, Adriano Fiorucci, Guido Peano, Bartolomeo Vigna   +4 more
doaj   +1 more source

Influence of Geometric Design on Mechanical Performance of Auxetic Metastructure

Advanced Engineering Materials, EarlyView.
Strategic geometric reinforcement transforms auxetic performance. This study evaluates 3D‐printed arrowhead metastructures, revealing that a modified design with local ring reinforcement suppresses premature failure to achieve superior energy absorption and structural efficiency.
Muhammad Gulzari, Supharoek Sornsomrit, Muhammad Ayaz Akbar, Stephan Rudykh   +3 more
wiley   +1 more source

Precipitation Simulations of the O‐Phase in Ti2AlNb Alloys Processed by Laser Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
Simulated and experimental evolution of the O‐phase volume fraction during postprocessing of a Ti‐21Al‐25Nb (at.%) alloy processed by laser powder bed fusion. With results of sensitivity to input parameters from a thorough and quantified analysis, the interfacial energy matrix/precipitate is the most relevant input parameter for the simulation of the O‐
Silvana Tumminello, Joachim Gussone, Suzana G. Fries, Marcus Rackel, Andreas Stark, Norbert Schell, Jan Haubrich, Guillermo Requena   +7 more
wiley   +1 more source

A Dislocation Perspective on Strength and Toughness in Ceramics

Advanced Engineering Materials, EarlyView.
Dislocations in ceramics enjoy a long but yet under‐appreciated history. The three research waves for dislocations in ceramics highlight the topic evolution over the last 90 years. This review focuses on the impact of dislocation on strength and toughness in ceramics.
Xufei Fang
wiley   +1 more source

Feasibility of Nitrogen as a Carrier Gas for Inconel Cold Spray in Hydropower Application

Advanced Engineering Materials, EarlyView.
N2, despite being nearly two orders of magnitude cheaper than He, is a feasible carrier gas for cold spray Inconel coatings in hydropower repair applications when higher gas temperature and pressure are used. Reducing powder size significantly improved cavitation resistance, while the addition of fine chromium carbide particles further enhanced erosion
Tianhao Wang, Mayur Pole, Tingkun Liu, Kenneth A. Ross, Christopher B. Smith   +4 more
wiley   +1 more source

Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading

Advanced Engineering Materials, EarlyView.
This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev, Noah‐Lean Roschlaub, Anne Jung   +2 more
wiley   +1 more source

Grain Refinement During Severe Plastic Deformation and Similitude of Subgrain Formation: A Molecular Dynamics Study

Advanced Engineering Materials, EarlyView.
Molecular dynamics is used to investigate structure refinement during severe plastic deformation. The results show similitude with experimental data. Molecular dynamics simulations of severe plastic deformation of monocrystalline and polycrystalline samples by multiaxial compression of aluminum are carried out.
Roberto B. Figueiredo
wiley   +1 more source

Advanced Electron Microscopy and Microcomputed Tomography Analysis of Single‐Crystal Ni‐Base Superalloys After Short‐Term Multiaxial Creep

Advanced Engineering Materials, EarlyView.
This work studies the anisotropic behavior of circular notched tensile specimens of Ni‐base superalloy single crystals during high‐temperature tensile creep along [001], [110], and [111]. Correlative scale‐bridging imaging of specimens reveals early rupture along [110] because 1) plastic deformation proceeds faster at notch center; 2) more (brittle ...
Leonardo Agudo Jácome, Lijie Cao, Christoph Somsen, Johannes Boes, René Hesse, Werner Theisen, Gunther Eggeler   +6 more
wiley   +1 more source