Results 171 to 180 of about 154,412 (250)

Inverse Identification of Energy‐Dependent Laser Absorptivity in NiTi Laser Powder‐Bed Fusion via Calibrated Melt Pool Simulation

Advanced Engineering Materials, EarlyView.
A combined experimental–computational framework identifies energy‐dependent laser absorptivity for NiTi in laser powder‐bed fusion, applicable to conduction and transition modes. Single‐track experiments and thermofluid smoothed particle hydrodynamics simulations are coupled through inverse analysis of melt pool geometry.
Mohamadreza Afrasiabi, Hadi Moutablaleh, Ignatius A. Setiawan, Mehrshad Mehrpouya   +3 more
wiley   +1 more source

Estimating and Measuring Methods of Residual Stresses Using Inherent strain Distribution Described as Functions. (Report 4). Function Expression for Inherent Strains in Fillet Welds and Its Accuracy.

QUARTERLY JOURNAL OF THE JAPAN WELDING SOCIETY, 1994
Ueda, Yukio, Ma, Ning Xu
openaire   +3 more sources

Development of 3D-Printed Cementitious Layered Model Rocks with Recycled Waste: A Study on Anisotropy. [PDF]

Materials (Basel)
Hu Y, Wang Y, Wang Z, Wang S, Hu J, Wang L, Xu X.   +6 more
europepmc   +1 more source

Lattice density distribution optimization based on recurrence relation inherent strain method

The Proceedings of Mechanical Engineering Congress, Japan, 2020
openaire   +2 more sources

Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading

Advanced Engineering Materials, EarlyView.
This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev, Noah‐Lean Roschlaub, Anne Jung   +2 more
wiley   +1 more source

An Impact Load History Reconstruction Method for Composite Structures Based on FBG Sensing Data and the GCV Principle. [PDF]

Sensors (Basel)
Zeng J, Xu J, Xu Y, Zhao X, Wang S, Zhou Y, Wang Y.   +6 more
europepmc   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Sparse polynomial surrogates for F-actin networks with compliant crosslinkers. [PDF]

Biomech Model Mechanobiol
Pacheco L, Parente M, Ferreira J.
europepmc   +1 more source

Design and Analysis of Compression–Torsion Coupling Metamaterials Using the Golden Section Method

Advanced Engineering Materials, EarlyView.
A novel compression–torsion metamaterial is engineered using inclined rods and symmetry breaking. To optimize its torsional performance, the golden section method is employed. The mechanical response of the metamaterial is validated through both numerical analysis and experimental validation.
Amirhossein Hassani, Sara Bagherifard
wiley   +1 more source

Thermal-driven H-bond reconfiguration for bioinspired high-strength anisotropic supramolecular hydrogels.

Mater Horiz
Wu J, Jiang P, Yang X, Bai C, Miao Z, Wang Y, Zhang H, Wang X.   +7 more
europepmc   +1 more source