Results 121 to 130 of about 2,272,899 (317)

Investigation of single and split injection strategies in an optical diesel engine

open access: yes, 2010
This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University, 22/12/2010.This study investigates the effects of a split injection strategy on combustion performance and exhaust emissions in a high speed direct ...
Herfatmanesh, Mohammad Reza
core  

Optimizing injection accuracy for Baxter’s nerve entrapment: an ultrasonography-guided approach based on anatomical surface landmarks

open access: yesAnnals of Medicine
Introduction The clinical feasibility and applicability of surface landmarks for Baxter nerve entrapment to proximal and distal sites is unclear. This study provides anatomical guidelines for optimal transducer placement using two specific landmarks, the
Jung-woo Choi   +6 more
doaj   +1 more source

The C‐terminal region of KIF26B is indispensable for nephron progenitor condensation and kidney formation in mice

open access: yesFEBS Open Bio, EarlyView.
KIF26B plays an important role in kidney development. We engineered mice lacking the C‐terminal region of KIF26B and found severe kidney defects, including bilateral renal agenesis, similar to full Kif26b knockout mice. The mutation disrupted nephron progenitor condensation and reduced Gdnf‐Wnt11 signaling, showing that the KIF26B C‐terminal region is ...
Yuta Yamamura   +19 more
wiley   +1 more source

Diesel Injection Analysis for New Premium Fuel Research and Emission Reduction

open access: yes, 2010
The objective of this study was to bring a scientific contribute in the problem of reducing diesel in-cylinder emissions, and releasing the diesel engine from its dependence on petroleum.
Caruso, Stephan
core  

Water Injection Effects on the Performance and Emission Characteristics of a CI Engine Operating with Biodiesel

open access: yes, 2012
Biodiesel is one of the most promising renewable, alternative and environmentally friendly biofuels that can be used in diesel engine without any need for any modification in the engine.
Gu, Fengshou   +11 more
core   +1 more source

Time‐restricted feeding prior to Mycobacterium tuberculosis infection reduces tissue CD4+ T cells with limited impact on bacterial clearance

open access: yesFEBS Open Bio, EarlyView.
Time‐restricted feeding (TRF) in mice increased liver fatty acid oxidation and decreased fatty acid biosynthesis. These alterations persisted when TRF was discontinued and the host was infected with Mycobacterium tuberculosis. Pre‐exposure to TRF did not alter tissue (lung and spleen) mycobacterial burden but significantly reduced CD3+ T cells in lungs
Ashish Gupta   +7 more
wiley   +1 more source

Achieving Representative Faultloads in Software Fault Injection

open access: yes, 2011
Given the complexity of modern software systems and its pervasiveness in many aspects of our lives, software faults (i.e., bugs) are a dangerous threat.
Natella, Roberto
core  

INFORMATION MODELING OF FUEL DISPERSION AND VAPORATION IN DIESEL ENGINE

open access: yesAdvanced Engineering Research, 2012
To settle upon the appropriate description of such processes as fuel injection, dispersion and vaporation in the diesel engines, a hierarchy of the corresponding models is offered.
Evgeny N. Ladosha   +2 more
doaj  

Cyclic azapeptide CD36 ligand attenuates cardiac injury and reduces long‐chain fatty acid accumulation after myocardial ischemia–reperfusion in mice

open access: yesFEBS Open Bio, EarlyView.
In a murine model of myocardial ischemia and reperfusion (MI/R), the CD36 azapeptide ligand MPE‐298 reduces cardiac injury and transiently lowers left ventricular long‐chain fatty acids (LCFAs) accumulation 3 h after reperfusion, accompanied by a decrease of oxidative stress and inflammation‐associated genes' expression in the heart and adipose tissue.
Jade Gauvin   +12 more
wiley   +1 more source

A Computational Model for Continuous Cooling of Injection Moulding Processes

open access: yes, 2008
This paper discusses the approaches and techniques used to build a realistic numerical model to analyse the cooling phase of the injection moulding process.
Smith, AG   +4 more
core  

Home - About - Disclaimer - Privacy