Results 1 to 10 of about 13,722 (215)
Thermomechanical properties of 3D-printed sand moulds using inorganic binder [PDF]
Heliyon, 2023 Additive Manufacturing of 3D-printed sand cores using the binder jetting process is well-established in prototype manufacturing. Due to the rising focus on sustainability and the fact that printed cores are shifting to serial production, a transition ...
Jochen Wendling +4 more
doaj +2 more sources
Journal of Asian Ceramic Societies, 2020 In the mineral insulation board industry, it has been a challenge to replace the current organic binder to eco-friendly inorganic binder to enhance the fire-resistance, and reduce toxicity.
Hyunseok Ko, Hyung Mi Lim
exaly +2 more sources
Enhanced green density of binder jetted tungsten heavy alloys with an inorganic metal salt binder
Journal of Materials Research and TechnologyBinder jetting (BJ) possesses considerable potential in forming complex tungsten heavy alloy components. Nonetheless, it is also confronted with challenges such as low green density.
Qingsong Wei, Kunhao Feng, Yuhua Heng
exaly +3 more sources
Lamellar-Structured Al2O3-SiO2 Nanofibrous Aerogels with Favorable Compression Resilience for Efficient High-Temperature Thermal Insulation [PDF]
MoleculesCeramic nanofiber-based materials have wide applicability in high-temperature management and protection. The transformation of conventional two-dimensional ceramic nanofibrous membranes into three-dimensional nanofiber-based bulks can effectively improve
Yuxin Ma +7 more
doaj +2 more sources
The Use of Phosphate Binder for Ablation Casting of AlSi7Mg Modified TiB Alloy [PDF]
Archives of Foundry Engineering, 2022 The possibilities of using an inorganic phosphate binder for the ablation casting technology are discussed in this paper. This kind of binder was selected for the process due to its inorganic character and water-solubility. Test castings were made in the
S. Puzio +3 more
doaj +1 more source
Journal of Materials Research and Technology, 2022 Generally, sand casted Al–Li alloy castings have very serious problems in pore defect and interfacial reaction, remarkably weakening the Al–Li alloy castings quality. How to solve these problems is always a challenge.
Yuancai Xu +5 more
doaj +1 more source
Science and Engineering of Composite Materials, 2022 In this article, aiming at the problems of low mechanical properties and the unstable structure of the binder in inorganic artificial stone, performance improvements were studied. The effects of 12 materials of blast-furnace slag (BFS), fly ash (FA), and
Huang Yifeng +7 more
doaj +1 more source
Radiological and physico-chemical characterization of red mud as an Al-containing precursor in inorganic binders for the building industry [PDF]
Nuclear Technology and Radiation Protection, 2021 The potential re-use of red mud in the building and construction industry has been the subject of research of many scientists. The presented research is a contribution to the potential solution of this environmental issue through the synthesis ...
Kljajević Ljiljana M. +6 more
doaj +1 more source
Case Studies in Construction Materials, 2023 Inorganic nanomaterials are widely studied to modify asphalt binder. However, the problems caused by poor compatibility and high viscosity have not been well resolved, and hence their further application is still limited. In order to break the limitation,
Jun Cai +5 more
doaj +1 more source
Investigation of the Granulometric and Mechanical Properties of Inorganic Used Sand
International Journal of Engineering and Management Sciences, 2020 This paper examines the use of a modified inorganic binder in metal-alloy casting. The results of investigations regarding the effect of reusing the used sand multiple times without reclamation. The technological properties of silica sand with inorganic
Viktória Dargai, László Varga
doaj +1 more source