Results 121 to 130 of about 12,949 (169)

A Novel Approach to Estimate the Transition Temperature via Dynamic Nanoindentation

Advanced Engineering Materials, EarlyView.
A new dynamic nanoindentation‐based method was developed that uses the stiffness ratio as an indicator of the elastic–plastic deformation contributions at different temperatures. The approach successfully identified transition temperatures in ferritic steel and distinguished them from continuously ductile austenitic steel.
Stefan Zeiler, Nikolaus Kostwein, Ronald Schnitzer, Christian Mitterer, Verena Maier‐Kiener   +4 more
wiley   +1 more source

Aptamer-based DNA nanoswitches for multiplexed protein detection.

Chem Commun (Camb)
Kovvali S, Beckles CA, Chandrasekaran AR, Halvorsen K.   +3 more
europepmc   +1 more source

Generalized self-calibrating probe approach for CW tissue oximetry. [PDF]

J Biomed Opt
Motamed Jahromi L, Yang L, von Lühmann A, Grosenick D.   +3 more
europepmc   +1 more source

Cryogenic Deformation Behavior of TiAl and Insights Into Embrittlement After High‐Temperature Exposure Combined With Secondary Ion Mass Spectroscopy of Near Surface Chemistry

Advanced Engineering Materials, EarlyView.
Near‐surface deuterium enrichment profiles for different microstructural types of TiAl after exposure at 700 °C in a heavy water‐containing environment. The deuterium levels are significantly higher than expected from natural occurrence, indicating that the heavy water dissociated during the exposure treatment and entered the specimens.
Jonathan D. H. Paul, Alexander Welle, Dirk Matthiessen, Michael Oehring, Fritz Appel, Florian Pyczak   +5 more
wiley   +1 more source

A feasibility study of chromatographic methods with mass spectrometry, flame ionization detector (FID), and micro electron capture detector (μECD) for laboratory adoption of organic gunshot residue analysis at trace levels. [PDF]

J Forensic Sci
Fiordigigli A, Ledergerber T, Joshi M, Dalzell K, Trejos T, Arroyo L.   +5 more
europepmc   +1 more source

3D‐Printed Titanium Gyroid Scaffold Structure Integrated With Tough Hybrid Materials for Cartilage Replacement

Advanced Engineering Materials, EarlyView.
This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin, Gloria R. Young, Francesca Tallia, Reece N. Oosterbeek, Shaaz Ghouse, Edward Spiers, Nupur Kohli, Tom Briggs, Marc Masen, Siwei Li, Ren‐Jei Chung, Jonathan R. T. Jeffers, Julian R. Jones   +12 more
wiley   +1 more source

Real-time energy measurement of clinical carbon ion beams using a cross-correlation time-of-flight method with parallel-plate chambers. [PDF]

Med Phys
Kwon NH, Choi SW, Han S, Yun Y, Han MC, Hong CS, Kim HJ, Lee H, Kim C, Kim DW, Koom WS, Kim JS, Carolino N, Lopes L, Kim DW, Fonte PJR.   +15 more
europepmc   +1 more source

The Role of Ultra‐Thin Passive Films and Organic Adsorbates on Aluminum Chips for a Friction‐Induced Solid‐State Recycling Process

Advanced Engineering Materials, EarlyView.
Despite benefits to storage stability and handleability of aluminum scrap, octadecyl phosphonic acid (ODPA) SAMs reduce the tensile strength of wires produced using friction‐induced recycling. Etching and methyl diphosphonic acid (MDPA) coatings, however, have little effect.
Timothy D. Goller, Steffen Gabsa, Werner Homberg, Guido Grundmeier   +3 more
wiley   +1 more source

Dosimetric characterization of CdZnTe radiation detectors under electron-beam irradiation. [PDF]

PLoS One
Park C, Seo J, Kim S, Kim H, Yeom JY, Cho S.   +5 more
europepmc   +1 more source

Elastic–Plastic Modeling and Experimental Characterization of Granular Jamming Actuators

Advanced Engineering Materials, EarlyView.
Granular jamming enables rapid switching between soft and rigid mechanical states. Here, a reduced‐order elastic‐perfectly‐plastic beam framework captures pressure‐dependent loading, unloading, residual deformation, and hysteresis in jammed beams, while matching three‐point bending experiments across materials and geometries. The framework links design
Saheli Patel, Prashant K. Purohit, Jordan R. Raney   +2 more
wiley   +1 more source