Results 141 to 150 of about 48,063 (294)

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

A Numerical–Experimental Approach for Multi‐Matrix Fiber‐Reinforced Plastics Characterization Using Finite Element Model Updating

Advanced Engineering Materials, EarlyView.
A numerical–experimental framework is developed for characterizing multi‐matrix fiber‐reinforced polymers (MM‐FRPs) combining epoxy and polyurethane matrices. Harmonic bending tests are integrated with finite element model updating (FEMU) to simultaneously identify elastic and viscoelastic material parameters.
Rodrigo M. Dartora, Tales V. Lisbôa, Axel Spickenheuer, Rogério J. Marczak, Jakson M. Vassoler   +4 more
wiley   +1 more source

Handbook of Establishing and Maintaining Oxygen‐Free Atmospheres

Advanced Engineering Materials, EarlyView.
This study presents a practical framework for creating oxygen‐free atmospheres at ambient pressure using silane‐doped inert gases. The results show that ultra‐low oxygen levels and strongly reduced water content can be achieved through controlled silane dosing, drying systems, and sensor monitoring.
Sascha Jan Zimmermann, René Gustus, Lienhard Wegewitz, Wolfgang Maus‐Friedrichs   +3 more
wiley   +1 more source

Application of Raman and Photoluminescence Spectroscopy to MgO‐C Refractories

Advanced Engineering Materials, EarlyView.
Visible to near infrared luminescence of MgO is studied on MgO‐C bricks and nominally pure MgO powder, with focus on two similar sharp high‐intensity signals, at 699 and 871 nm, each surrounded by symmetrical sidebands. The nature of these sidebands is investigated by temperature‐dependent spectroscopic measurements, confirming phonon involvement by ...
Julia Richter, Felix Drechsler, Till M. J. Stadtmüller, Cameliu Himcinschi, Christos G. Aneziris, Jens Kortus   +5 more
wiley   +1 more source

Phenomenological and Physically Based Modeling of Flow Stress and Strengthening Mechanism of Inconel 718

Advanced Engineering Materials, EarlyView.
Nickel‐based alloys are widely used in high‐temperature applications due to their excellent mechanical strength and oxidation resistance. However, properties such as high‐temperature strength and pronounced work‐hardening make them difficult to machine.
Soheil Rooein, Oliver Schenk, Christoph Broeckmann   +2 more
wiley   +1 more source

Investigation of Thermo‐Chemical Processes in Commercial MgO‐C Refractory Bricks With and Without MgO‐C Recyclate at Elevated Temperatures

Advanced Engineering Materials, EarlyView.
This study investigates thermo‐chemical processes during high‐temperature testing of two commercial MgO‐C brick grades, one containing 47.5 wt.% MgO‐C recyclate. Using ETV, DTA/TG‐MS, XRD, and SEM/EDS/EBSD, mechanisms such as carbothermal reduction of magnesia, impurity incorporation into the secondary MgO surface layer, and calcium‐rich phase ...
Alexander Schramm, Jana Hubálková, Christian Schimpf, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +6 more
wiley   +1 more source

Combined Process‐ and Phase‐Field‐Simulation to Predict the Microstructure of Single‐Crystal Ni‐Based Superalloys

Advanced Engineering Materials, EarlyView.
A combined finite element and phase‐field approach predicts the evolution of microstructure during the directional solidification of Ni‐based superalloys. The model reveals how withdrawal rate, temperature gradient, and wall thickness control the dendrite spacing, highlighting the strong effect of surface regions in thin sections where dendrite growth ...
Sean Böhm, André B. Baldissera, Rainer Völkl, Uwe Glatzel   +3 more
wiley   +1 more source

Liouville theory: an introduction to rigorous approaches

Journal of High Energy Physics
In recent years, a surprisingly direct and simple rigorous understanding of quantum Liouville theory has developed. We aim here to make this material more accessible to physicists working on quantum field theory.
Sourav Chatterjee, Edward Witten
doaj   +1 more source

Alternate approach to no integrability field theory

Mathematical and Computer Modelling, 1989
This is another paper in a series which illustrates that foregoing the rules of traditional calculus opens up a realm of possibilities. We study the ''aesthetic field theory'', although the techniques are more general. We introduce a new integration procedure which is consistent with aesthetic principles.
openaire   +1 more source

Al–Cu Composite Casting of Laser‐Deoxidized Copper: Bonding, Interfacial Chemistry, and Thermal Conductivity

Advanced Engineering Materials, EarlyView.
This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff, Finn‐Lennard Janthur, Sascha Zimmermann, Sarah Seffer, Jörg Hermsdorf, René Gustus, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Christian Klose   +9 more
wiley   +1 more source