Results 181 to 190 of about 16,522 (296)

A Dislocation Perspective on Strength and Toughness in Ceramics

Advanced Engineering Materials, EarlyView.
Dislocations in ceramics enjoy a long but yet under‐appreciated history. The three research waves for dislocations in ceramics highlight the topic evolution over the last 90 years. This review focuses on the impact of dislocation on strength and toughness in ceramics.
Xufei Fang
wiley   +1 more source

Computational study of unsteady Homann type flow of ternary hybrid nanofluid in the presence of induced magnetic forces and time relaxation. [PDF]

Discov Nano
Ahmad L, Khan AA, Javed S, Khan U, Bashatah JA.   +4 more
europepmc   +1 more source

Inverse Identification of Energy‐Dependent Laser Absorptivity in NiTi Laser Powder‐Bed Fusion via Calibrated Melt Pool Simulation

Advanced Engineering Materials, EarlyView.
A combined experimental–computational framework identifies energy‐dependent laser absorptivity for NiTi in laser powder‐bed fusion, applicable to conduction and transition modes. Single‐track experiments and thermofluid smoothed particle hydrodynamics simulations are coupled through inverse analysis of melt pool geometry.
Mohamadreza Afrasiabi, Hadi Moutablaleh, Ignatius A. Setiawan, Mehrshad Mehrpouya   +3 more
wiley   +1 more source

2D Trefftz method in identification of flow boiling heat transfer coefficient in horizontal minichannel. [PDF]

Sci Rep
Grabowski M, Hożejowska S, Pawińska A, Poniewski ME.   +3 more
europepmc   +1 more source

Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading

Advanced Engineering Materials, EarlyView.
This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev, Noah‐Lean Roschlaub, Anne Jung   +2 more
wiley   +1 more source

Photothermal carbon black coatings enable efficient solar-driven membrane distillation. [PDF]

RSC Adv
Alshareef M, Mahmoud AM, Al-Ghamdi AS, Alhumade H, Mustafa I, Alotaibi MT, Alharbi A, Ebraheem B, Ali MEA.   +8 more
europepmc   +1 more source

Influence of Si Content and Milling Duration on the Microstructure and Mechanical–Tribological Properties of AlCoCrFeNiSi High‐Entropy Alloys

Advanced Engineering Materials, EarlyView.
Si‐doped AlCoCrFeNi high‐entropy alloys are synthesized by mechanical alloying to reveal the effect of Si content and milling time on phase evolution, microstructural refinement, and tribological behavior. A transition from FCC to BCC structure, significant grain refinement, and enhanced hardness and wear resistance are achieved, with the 4 at% Si ...
Mustafa Okumuş, Mehmet Emin Demir, Sercan Özpınar   +2 more
wiley   +1 more source

Conductive heat loss in simulated outdoor settings: a preliminary experimental human study. [PDF]

Int J Emerg Med
Sanak T, Putowski M, Krzeptowski-Sabała S, Pobędza J, Walczak P, Mendrala K, Darocha T, Kosiński S.   +7 more
europepmc   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Time-resolved imaging of electron beam powder bed fusion using an X-ray microscope optimized for white beam radiation. [PDF]

J Synchrotron Radiat
Bidola P, Semjatov N, Spartacus G, König HH, Abreu-Faria G, Klingenberg J, Brehling J, Krywka C, Staron P, Lindwall G, Körner C, Ioannidou C, Beckmann F.   +12 more
europepmc   +1 more source