Results 121 to 130 of about 222,035 (266)
Advanced Engineering Materials, EarlyView.The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Electrochemical modification of the liquid - liquid interface with mesoporous silica
Modification électrochimique de l'interface liquide - liquide avec de la silice mésoporeuse Ce travail combine l'électrochimie à l'interface liquide - liquide avec le procédé sol - gel pour la modification interfaciale avec de la silice mésoporeuse. Dans la première partie de ce travail, l’interface liquide – liquide macroscopique a été
openaire +2 more sources
Advanced Engineering Materials, EarlyView.This article presents the NFDI‐MatWerk Ontology (MWO), a Basic Formal Ontology‐based framework for interoperable research data management in materials science and engineering (MSE). Covering consortium structures, research data management resources, services, and instruments, MWO enables semantic integration, Findable, Accessible, Interoperable, and ...
Hossein Beygi Nasrabadi +4 more
wiley +1 more source
Influence of Interfacial Modification on EHL of Journal Bearing
Jixie chuandong, 2019 Considering the slipping boundary conditions， the limiting shear stress model and the line contact elastohydrodynamic lubrication model are established， the lubricant interfacial slip velocity is deduced and the fluid-lubricated Reynolds equation is ...
Yabo Zhou +3 more
doaj
Zein‐Based Adhesives: Sustainable Extraction and Application in Bioadhesive Technologies
Advanced Engineering Materials, EarlyView.Zein is extracted from corn gluten meal using a simple and scalable process with high yield (~90%). The resulting protein is applied in bioadhesives modified with Ca2+ and Fe3+ ions, exhibiting substrate‐dependent adhesion. The findings demonstrate competitive bonding performance and highlight the role of ionic interactions in tuning adhesion ...
Paula Bertolino Sanvezzo +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti +11 more
wiley +1 more source
Synergistic dual-interface modification for high-performance CsPbBr<sub>3</sub> perovskite solar cells: a combined experimental and modeling study. [PDF]
RSC AdvLi X, Bai Z, Chen Q, Zhang Z.
europepmc +1 more source
Bottom Contact Metal Oxide Interface Modification Improving the Efficiency of Organic Light Emitting Diodes. [PDF]
Materials (Basel), 2020 Pozov SM +6 more
europepmc +1 more source
Advanced Engineering Materials, EarlyView.Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar +2 more
wiley +1 more source