Results 161 to 170 of about 920,820 (244)
Some of the next articles are maybe not open access.
Composites Part A: Applied Science and Manufacturing, 2018
Due to poor wettability and low reactivity, the interfacial adhesions between CF and PEEK matrix are relatively weak, significantly affecting mechanical performances of composites, especially the interlaminar shear strength.
Shu Zhu, Elwathig Hassan
exaly +2 more sources
Due to poor wettability and low reactivity, the interfacial adhesions between CF and PEEK matrix are relatively weak, significantly affecting mechanical performances of composites, especially the interlaminar shear strength.
Shu Zhu, Elwathig Hassan
exaly +2 more sources
Comparison of the short beam shear (SBS) and interlaminar shear device (ISD) tests
Composites Part A: Applied Science and Manufacturing, 1997The Short Beam Shear (SBS) and Interlaminar Shear Device (LSD) tests are compared as methods for determining interlaminar shear strength of thermoplastic composite rings. The rings were manufactured using laser-assisted on-line consolidation and the interlaminar shear strength is taken as a measure of the quality of parts subjected to various ...
F. Rosselli, M.H. Santare
exaly +2 more sources
Composite Interfaces, 1998
By measuring the contact electrical resistance of the interlaminar interface of a unidirectional continuous carbon fiber epoxy-matrix composite during shear, the interlaminar shear process was monitored in real time. The resistance increased throughout the entire shear process for a low curing pressure, but decreased in the initial stage of shear for a
D D L Chung, Shoukai Wang
exaly +2 more sources
By measuring the contact electrical resistance of the interlaminar interface of a unidirectional continuous carbon fiber epoxy-matrix composite during shear, the interlaminar shear process was monitored in real time. The resistance increased throughout the entire shear process for a low curing pressure, but decreased in the initial stage of shear for a
D D L Chung, Shoukai Wang
exaly +2 more sources
In-plane and interlaminar shear properties of carbon/epoxy laminates
Composites Science and Technology, 1995Abstract Carbon/epoxy laminates of three different lay-ups have been tested to measure both in-plane shear and interlaminar shear (ILS) properties by the Iosipescu shear method. A reasonably pure state of shear strain is achieved in the region between the roots of two V-notches in all the laminates.
G. Zhou, E.R. Green, C. Morrison
exaly +2 more sources
, 2021
This study investigates the interlaminar shear behavior of 3D printed CFRP composites fabricated by fused deposition modeling (FDM) through a combined experimental and numerical study.
Denizhan Yavas +3 more
semanticscholar +1 more source
This study investigates the interlaminar shear behavior of 3D printed CFRP composites fabricated by fused deposition modeling (FDM) through a combined experimental and numerical study.
Denizhan Yavas +3 more
semanticscholar +1 more source
, 2021
Interlaminar shear strength (ILSS) is an important quality indicator to evaluate laminates, which requires further studies to produce high-quality laminates by automated placement.
Miao Qiuyu +4 more
semanticscholar +1 more source
Interlaminar shear strength (ILSS) is an important quality indicator to evaluate laminates, which requires further studies to produce high-quality laminates by automated placement.
Miao Qiuyu +4 more
semanticscholar +1 more source
International Journal on Road Materials and Pavement Design, 2022
The asphalt pavement with heating cables (APHC) was widely used for snow/ice-melting. However, the adverse effects of heating cables on the interlaminar stability of APHC was neglected.
Kai Liu +5 more
semanticscholar +1 more source
The asphalt pavement with heating cables (APHC) was widely used for snow/ice-melting. However, the adverse effects of heating cables on the interlaminar stability of APHC was neglected.
Kai Liu +5 more
semanticscholar +1 more source
Investigation of the In-Plane Shear and Interlaminar Shear in Woven Roving Composites
Fibers and Polymers, 2021In this paper a computational and experimental study to determine the in plane and interlaminar shearing stress-strain response of a composite material is performed. It is known that the above mentioned shear properties can be directly determined from shear and torsion experiments but also can indirectly be determined from bending and tension ...
S. Strapatsakis +2 more
openaire +1 more source
, 2021
The present paper regards the shear strengthening of fiber metal laminates (FMLs) composed by surface treated magnesium and carbon fiber reinforced epoxy (CFRP) laminates.
M. Ostapiuk +3 more
semanticscholar +1 more source
The present paper regards the shear strengthening of fiber metal laminates (FMLs) composed by surface treated magnesium and carbon fiber reinforced epoxy (CFRP) laminates.
M. Ostapiuk +3 more
semanticscholar +1 more source
, 2021
Fiber-reinforced thermoplastic composites offer a high potential for high-volume car body structures. A tailored use of thermoformed and subsequently injection overmolded unidirectional pultruded material in the so-called “skeleton design” is a promising
A. Maier, N. Schramm, L. Kroll
semanticscholar +1 more source
Fiber-reinforced thermoplastic composites offer a high potential for high-volume car body structures. A tailored use of thermoformed and subsequently injection overmolded unidirectional pultruded material in the so-called “skeleton design” is a promising
A. Maier, N. Schramm, L. Kroll
semanticscholar +1 more source