Results 11 to 20 of about 5,244 (242)
Research on Influence mechanism of composite interlaminar shear strength under normal stress
Science and Engineering of Composite Materials, 2020 The normal stress along the shear plane has great effect on the composite intralaminar shear strength. However, the influence mechanism on composite interlaminar shear strength under the normal stress along the shear plane was not truly reflected by the ...
Li Fei +3 more
doaj +2 more sources
Interlaminar Shear Properties of Bamboo Composite for Structural Applications
Fibers, 2022 Interlaminar shear strength in bamboo composite (BC) is mainly provided by epoxy resin as the matrix in BC. This may greatly change due to humidity.
Ali Rajabipour +3 more
doaj +3 more sources
An Interlaminar Shear Test for Fibre-Reinforced Plastics
Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, 1993 The measurement of the interlaminar shear strength of glass-reinforced plastic (GRP) laminates is proposed using an offset four-point bend test on a beam where two (P) of the four forces differ from the other two (Q) and the ratio λ = P/Q depends upon the relative positions along the beam.
Sideridis, E. +2 more
openaire +3 more sources
Interlaminar Shear Properties of Z-Pinned Carbon Fiber Reinforced Aluminum Matrix Composites by Short-Beam Shear Test. [PDF]
Materials (Basel), 2018 This paper presents the effect of through-thickness reinforcement by steel z-pins on the interlaminar shear properties and strengthening mechanisms of carbon fiber reinforced aluminum matrix composites (Cf/Al) with a short beam shear test method ...
Wang S, Zhang Y, Wu G.
europepmc +2 more sources
Cailiao gongcheng, 2023 Two different sizes of graphene oxide (GO) produced by the Hummers method had been incorporated into epoxy resins and used to fabricate GO modified carbon fiber reinforced epoxy resin composites (GO/CF/EP) by compression molding method, and the composite
REN Mingwei +7 more
doaj +1 more source
Materials & Design, 2021 To improve the interlaminar properties of carbon fiber reinforced polymer composites (CFRPs), a hybrid fiber mat (i-MBP-PCF) was prepared by in situ deposition of a multiwalled carbon nanotube buckypaper (i-MBP) on the surface of functionalized CF fabric
Yadong Wu +6 more
doaj +1 more source
The influence of hydrostatic pressure on the interlaminar fracture toughness of carbon/epoxy composites [PDF]
, 2006 The use of composites for deep sea applications requires a thorough understanding of the behaviour of these materials. While several studies have examined the influence of pressure on in-plane properties few data are available for the interlaminar ...
Peleau, M. +3 more
core +1 more source
About the impact behavior of woven-ply carbon fiber-reinforced thermoplastic- and thermosetting-composites: A comparative study [PDF]
, 2013 This study is aimed at comparing the response of TS-based (epoxy) and TP-based (PPS or PEEK) laminates subjected to low velocity impacts. C-scan inspections showed that impact led to diamond-shaped damage resulting from different failure mechanisms ...
Vieille, Benoit +5 more
core +1 more source
Frontiers in Materials, 2020 The main objectives of this article were to examine the feasibility of high quality laminate (carbon PEKK—Poly-Ether-Ketone-Ketone) manufacturing under low pressure and to analyze the principal phenomena governing the consolidation quality.
Florence Saffar +6 more
doaj +1 more source
Finite element analyses of mode I interlaminar delamination in z-fibre reinforced composite laminates. [PDF]
, 2003 This paper presents a detailed numerical study of the mode I interlaminar fracture of carbon/epoxy composite laminates with z-fibre reinforcement. The study was performed using a double cantilever beam configuration.
Marcello Grassi +3 more
core +1 more source