Results 21 to 30 of about 4,119 (241)

Influence of size of graphene oxide on interfacial properties of carbon fiber/epoxy resin under damp and heat conditions

Cailiao gongcheng, 2023
Two different sizes of graphene oxide (GO) produced by the Hummers method had been incorporated into epoxy resins and used to fabricate GO modified carbon fiber reinforced epoxy resin composites (GO/CF/EP) by compression molding method, and the composite
REN Mingwei, ZI Yaxian, ZHANG Ying, ZHOU Yujing, QIU Hong, LIU Gang, BAI Hua, HU Xiaolan   +7 more
doaj   +1 more source

The influence of hydrostatic pressure on the interlaminar fracture toughness of carbon/epoxy composites [PDF]

, 2006
The use of composites for deep sea applications requires a thorough understanding of the behaviour of these materials. While several studies have examined the influence of pressure on in-plane properties few data are available for the interlaminar ...
Peleau, M., Davies, P., Cartié, Denis D. R., Partridge, Ivana K.   +3 more
core   +1 more source

Effect of simulated hygrothermal environment on the flexural and interlaminar shear strength of particulate-filled epoxy-coated GFRP composites

, 2022
The application of glass fiber-reinforced polymer (GFRP) composites in civil engineering and construction has gained significant interest in the last decade.
Sorbello, C.-D., Gerdes, Andreas, Ferdous, W., Manalo, A., Benmokrane, B., Manalo, Allan, Alajarmeh, O., Alajarmeh, Omar, Ferdous, Wahid, Benmokrane, Brahim, Sorbello, Charles-Dean   +10 more
core   +1 more source

Interlaminar Shear Properties of Bamboo Composite for Structural Applications

Fibers, 2022
Interlaminar shear strength in bamboo composite (BC) is mainly provided by epoxy resin as the matrix in BC. This may greatly change due to humidity.
Ali Rajabipour, Alireza Javadian, Milad Bazli, Mark Masia   +3 more
doaj   +1 more source

Finite element analyses of mode I interlaminar delamination in z-fibre reinforced composite laminates. [PDF]

, 2003
This paper presents a detailed numerical study of the mode I interlaminar fracture of carbon/epoxy composite laminates with z-fibre reinforcement. The study was performed using a double cantilever beam configuration.
Marcello Grassi, Xiang Zhang, Zhang, Xiang, Grassi, Marcello   +3 more
core   +1 more source

About the impact behavior of woven-ply carbon fiber-reinforced thermoplastic- and thermosetting-composites: A comparative study [PDF]

, 2013
This study is aimed at comparing the response of TS-based (epoxy) and TP-based (PPS or PEEK) laminates subjected to low velocity impacts. C-scan inspections showed that impact led to diamond-shaped damage resulting from different failure mechanisms ...
Vieille, Benoit, Bouvet, Christophe, V.M. Casado, Casado, Victor Manuel, C. Bouvet, B. Vieille   +5 more
core   +1 more source

Statistical evaluation of the effect of hygrothermal aging on the interlaminar shear of GFRP��

Fracture and Structural Integrity, 2022
The studies of patterns of changes in properties, accumulation of damages and failure of structural composites after hygrothermal aging represent a relevant and important area.
Dmitrii S. Lobanov, Andrey S. Yankin, Nataliya I. Berdnikova�   +2 more
doaj   +1 more source

Interlaminar Shear Fatigue Strength of GFRP.

Journal of the Society of Materials Science, Japan, 1992
The purpose of this research was to study the fatigue behaviour and the test method for S2 glass fibre reinforced plastic under an interlaminar shear fracture mode. Fatigue tests were carried out under the short beam shear (SBS) condition of three point bending. The main results obtained are as follows.
OKADA, Tomonobu, KOE, Shigeki, KODAI, Aki, BANDOH, Shun-ichi   +3 more
openaire   +2 more sources

In-situ Monitoring of the Out-Of-Autoclave Consolidation of Carbon/Poly-Ether-Ketone-Ketone Prepreg Laminate

Frontiers in Materials, 2020
The main objectives of this article were to examine the feasibility of high quality laminate (carbon PEKK—Poly-Ether-Ketone-Ketone) manufacturing under low pressure and to analyze the principal phenomena governing the consolidation quality.
Florence Saffar, Florence Saffar, Florence Saffar, Camille Sonnenfeld, Pierre Beauchêne, Chung Hae Park, Chung Hae Park   +6 more
doaj   +1 more source

Enhancement of the interlaminar performance of silica/phenolic laminates after high-temperature pyrolysis using a boron carbide/silicon carbide fibre z-pin

Materials & Design, 2022
The interlaminar strength of polymer matrix laminates significantly affects their performance. Z-pinning is an effective method for improving the interlaminar performance of laminates.
Huadong Fu, Yan Qin, Zhenyue Zou, Jiamin Fan, Chenyi Xue   +4 more
doaj   +1 more source