Results 161 to 170 of about 3,100,919 (260)

Wood‐Derived Nanocellulose‐Biocarbon Fresnel‐Zone Plate Lenses for Sub‐THz Frequency Applications

Advanced Materials Technologies, EarlyView.
Wood‐derived nanocellulose and lignin‐based biocarbon were combined to fabricate fully bio‐based Fresnel zone plate (FZP) lenses for sub‐terahertz frequencies. These sustainable FZP lenses exhibit low dielectric loss and high directivity, achieving performance comparable to that of metallic references, and remain functional under environmental stress ...
Riikka Haataja, Mikko Kokkonen, Niina Halonen, Sami Myllymäki, Umair Rafique, Mandeep Singh, Ossi Laitinen, Heli Jantunen, Kristiina Oksman, Henrikki Liimatainen   +9 more
wiley   +1 more source

Photoluminescence Reshaping via Structural Confinement and Local Density of Optical States Control in Ir(III)‐Doped Biodegradable Metasurfaces

Advanced Materials Technologies, EarlyView.
Phosphorescent biodegradable metasurface showing vibronic selection and spectral photoluminescence narrowing. Anti‐correlation between experimental LDOS and measured lifetimes. ABSTRACT Metasurfaces incorporating phosphorescent emitters offer a route to engineer radiative and vibronic processes beyond chemical design.
Vincenzo Caligiuri, Andrea Smeriglio, Svetlana Siprova, Olga Favale, Francesca Leone, Roberto Termine, Debora Policastro, Alessandra Crispini, Attilio Golemme, Nicolas Godbert, Iolinda Aiello, Antonio De Luca   +11 more
wiley   +1 more source

Moisture‐Adaptive Triboelectric Materials and Platforms: Design Strategies, Performance Enhancement, and Applications in Energy Harvesting and Wearable Electronics

Advanced Materials Technologies, EarlyView.
This review summarizes moisture‐adaptive strategies that enable triboelectric nanogenerators (TENGs) to operate across diverse moisture conditions. It examines moisture‐management methods, including exclusion, directional transport, removal, and utilization, with charge‐regulation approaches based on interfacial, dielectric, and structural engineering.
Junzhe Gan, Zhao Sha, Xuehua Zhang, Hoang‐Phuong Phan, Jin Zhang   +4 more
wiley   +1 more source

Programming Actuation in 3D‐Printed Micro‐Architectures via Interfacial Adhesion Control

Advanced Materials Technologies, EarlyView.
A two‐phase meniscus‐guided 3D printing method directly fabricates microscale poly(3,4‐ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) and poly(vinyl alcohol) (PVA) bilayers with in situ programmable interfaces. Modulating the meniscus stretching speed switches the interface between separated and bonded states, which controls the mechanical ...
Xiao Huan, Juhyung Kim, Yujin Park, Shiqi Hu, Jihyuk Yang, Nan Huang, Feipeng Chen, Yu Liu, Sixi Cao, Zhuoran Wang, Ho Cheung Shum, Barbara Pui Chan, Dongwoon Shin, Ji Tae Kim   +13 more
wiley   +1 more source

Chitin‐Chitosan Cryogels for the Reversible Sequestration and Recovery of Heavy Metals From Wastewater

Advanced Materials Technologies, EarlyView.
Chitin‐chitosan cryogels with degrees of N‐acetylation from 12.2% to 71.4% are fabricated by dissolution, coagulation and lyophilization for the sequestration of heavy metals from water. Colorimetry and differential pulse voltammetry showed controlled adsorption and desorption capacities for As5+, Co2+ and Cu2+, making this material attractive for ...
Marta García‐Castrillo, Maialen Uribarrena, Jorge Sáiz, Guillermo Copello, Erlantz Lizundia   +4 more
wiley   +1 more source

Extrusion‐Based Bioprinting of Living Bioinks for Tissue and Organ Engineering

Advanced Materials Technologies, EarlyView.
Extrusion‐based bioprinting is presented as the most versatile route for fabricating living, heterogeneous tissues. Its ability to combine diverse bioinks, support matrices, and advanced printhead geometries transforms familiar constraints into powerful biofabrication opportunities.
Eric Silberman, Ester Sapir Baruch, Roni Cohen, Assaf Shapira, Tal Dvir   +4 more
wiley   +1 more source

Transparent Single‐Dye NIR Photonic Platform for Multimodal Optical Authentication

Advanced Optical Materials, EarlyView.
A single‐component DHP‐SQ dye integrates visible transparency, near‐infrared (NIR) fluorescence, and photothermal functionality into one molecular platform. NIR‐selective visualization transforms visually imperceptible printed patterns into readily authenticated information, while screen‐printing compatibility enables well‐defined patterning on diverse
Su Jeong Choi, Seung Hyeon Kim, Dayoung Shin, Yeongnam Heo, Minseo Kim, Ji Hyeon Lee, Ji‐Eun Jeong, Young‐Jae Jin, Jin Chul Kim, Hyoung Eun Bae, Young Hoon Son, Sung Jin Park, Sang Hwan Nam, Young Il Park, Hyocheol Jung   +14 more
wiley   +1 more source

Information Transmission Strategies for Self‐Organized Robotic Aggregation

Advanced Robotics Research, EarlyView.
In this review, we discuss how information transmission influences the neighbor‐based self‐organized aggregation of swarm robots. We focus specifically on local interactions regarding information transfer and categorize previous studies based on the functions of the information exchanged.
Shu Leng, Zihan Li, Yifeng Shao, Jinhao Liu, Li Yu, Shuguang Li   +5 more
wiley   +1 more source

Molecular Appendix Adjusted Architectural Propagations of Red‐Light Controlled Macroscopic Photoactuating Performances

Advanced Robotics Research, EarlyView.
Amphiphilic chloroazobenzenes, bearing different amino acids as end groups alanine, phenylalanine, and valine, exhibit excellent photoisomerizations. Varying structures of three amino acid groups participate in supramolecular formations and therefore photoinduced morphological transformations via adjusting intermolecular interactions. These interaction
Shuangshuang Meng, Ming‐Hin Chau, Takashi Kajitani, Franco King‐Chi Leung   +3 more
wiley   +1 more source

3D Printing of Self‐Healing Polymers by Material Extrusion: A Process‐Centric Review of Setups, Parameters, and Applications

Advanced Robotics Research, EarlyView.
This review highlights recent advances in material extrusion 3D printing of self‐healing polymers, focusing on the interplay between material chemistry, rheology, hardware customization, and process optimization. Filament‐ and ink‐based extrusion strategies, multimaterial architectures, and postprocessing approaches are discussed for applications in ...
Antonio Pavone, Gianni Stano, Gianluca Percoco   +2 more
wiley   +1 more source