Results 211 to 220 of about 16,925,605 (335)

Zein‐Based Adhesives: Sustainable Extraction and Application in Bioadhesive Technologies

Advanced Engineering Materials, EarlyView.
Zein is extracted from corn gluten meal using a simple and scalable process with high yield (~90%). The resulting protein is applied in bioadhesives modified with Ca2+ and Fe3+ ions, exhibiting substrate‐dependent adhesion. The findings demonstrate competitive bonding performance and highlight the role of ionic interactions in tuning adhesion ...
Paula Bertolino Sanvezzo, Daniela Winsley Valereto Friozi, Vinícius de Oliveira, Marcia Cristina Branciforti   +3 more
wiley   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

A simplified technique to isolate the porcine and human ileal intrinsic factor receptors and studies on their subunit structures.

Biochemical and Biophysical Research Communications - BBRC, 1979
I. Kouvonen, R. Gräsbeck
semanticscholar   +1 more source

Characterization of Nitinol Produced by Laser Powder Bed Fusion for Mechanical Metamaterial Applications

Advanced Engineering Materials, EarlyView.
Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek, Jakub Hurník, Miroslav Šmíd, Ondřej Zobač, Melanie Todt, Daniel Koutný   +5 more
wiley   +1 more source

Thermodynamic Pathways of Nonequilibrium Solidification in Wire‐Arc Additive Manufacturing Fe‐Based Multicomponent Alloy Structures

Advanced Engineering Materials, EarlyView.
Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios, Anthony Gonzalez, Aleksander Aleman, Tyler Dolmetsch, Tanaji Paul, Arvind Agarwal   +5 more
wiley   +1 more source

Tailored Hierarchical Porous Copper Architectures via Three Dimensional Printing and Pressure‐less Sintering for Next‐Generation Lithium‐Metal Batteries

Advanced Engineering Materials, EarlyView.
A hierarchical porous copper current collector is fabricated via three‐dimensional printing combined with pressureless sintering to stabilize lithium metal anodes. The interconnected architecture lowers local current density, guides uniform Li deposition within pores, and suppresses dendrite growth.
Alok Kumar Mishra, Mukul Shukla
wiley   +1 more source

Phenomenological and Physically Based Modeling of Flow Stress and Strengthening Mechanism of Inconel 718

Advanced Engineering Materials, EarlyView.
Nickel‐based alloys are widely used in high‐temperature applications due to their excellent mechanical strength and oxidation resistance. However, properties such as high‐temperature strength and pronounced work‐hardening make them difficult to machine.
Soheil Rooein, Oliver Schenk, Christoph Broeckmann   +2 more
wiley   +1 more source

Heteroepitaxial 3C-SiC for MEMS Applications. [PDF]

Micromachines (Basel)
Garofalo A, Muoio A, Belsito L, Sapienza S, Ferri M, Roncaglia A, La Via F.   +6 more
europepmc   +1 more source

Composition‐Tuned Enhancement of the Anomalous Nernst Effect in FeCo–Pt Thin Films on Rigid and Flexible Substrates

Advanced Engineering Materials, EarlyView.
Disordered (Fe50Co50)1−xPtx thin films exhibit a pronounced anomalous Nernst effect (ANE) with a strong composition dependence on both rigid and flexible substrates. The transverse thermoelectric response peaks near 22.5 at.% Pt, accompanied by enhanced αxy/σxy scaling, thermal transport, and ANE sensitivity.
Mojtaba Mohammadi, Hiroyuki Awano, Kenji Tanabe   +2 more
wiley   +1 more source

Research on the application behavior of generative artificial intelligence learning of college students based on self-determination theory. [PDF]

Front Psychol
Fang X, Feng J.
europepmc   +1 more source