Results 161 to 170 of about 60,685 (269)
Comparação técnico-económica entre sistemas com inversores centrais e sistemas com inversores string
, 2014 Devido ao aumento da importância da energia solar a nível mundial e à crescente demanda energética, tem-se verificado uma contínua aposta em parques fotovoltaicos cada vez maiores por todo o mundo, sendo necessário otimizar cada vez mais as soluções para que a eficiência seja maior e consequentemente o lucro também.
openaire +1 more source
México, un inversor estratégico para España
Boletín Económico de ICEMéxico es uno de nuestros principales socios comerciales y uno de nuestros destinos prioritarios de inversión. Desde hace al menos dos décadas se ha convertido además en uno de los principales inversores en nuestro país. El anuncio de operaciones que acaparan titulares en prensa por parte de empresas y grandes empresarios mexicanos, la consolidación de
Álvaro Pastor Escribano +2 more
openaire +1 more source
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
, 2016 Nuestra investigación se centra en la exégesis y análisis en profundidad de la doctrina española sobre el artículo 282 bis, aunque también haremos un largo recorrido por los supuestos y autores más importantes del derecho continental y anglosajón. Así como la obligada referencia a la normativa bursátil por excelencia, la LMV, analizando la remisión a ...
openaire +1 more source
Advanced Engineering Materials, EarlyView.Creep experiments at 900°C on coarse‐grained steel‐ceramic composites containing recycled magnesia reveal that higher ceramic volume fractions significantly enhance the creep resistance. Detailed EBSD investigations identify subgrain formation in the steel matrix as the dominant deformation mechanism.
Moritz Müller +6 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.A numerical–experimental framework is developed for characterizing multi‐matrix fiber‐reinforced polymers (MM‐FRPs) combining epoxy and polyurethane matrices. Harmonic bending tests are integrated with finite element model updating (FEMU) to simultaneously identify elastic and viscoelastic material parameters.
Rodrigo M. Dartora +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios +5 more
wiley +1 more source
Influence of the tilt angle of Percutaneous Aortic Prosthesis on Velocity and Shear Stress Fields [PDF]
Arq Bras Cardiol, 2017 Gomes BAA +6 more
europepmc +1 more source
Advanced Engineering Materials, EarlyView.Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm +5 more
wiley +1 more source
Balance control during gait initiation: State-of-the-art and research perspectives. [PDF]
World J Orthop, 2017 Yiou E +4 more
europepmc +1 more source